Show all posts by user
Page 1 of 1 Pages: 1
Results 1 — 21 of 21
There are plans for this, but I can not yet understand what license is better to use. In addition, it is unlikely to protect against Chinese copies
QuoteCthulhuLabs
Will you be providing all of the documentation including the original design files so that someone can build one of these boards themselves? Meaning if I wanted to I could order unpopulated PCBs and the individual components and popu
by
svs072477
-
Developers
I am now studying the options for open source licenses and how to get them. When I'm done, I'll publish the documentation
Quoteboelle
open source?
by
svs072477
-
Developers
Marlin 2.0
Mk4DUO
Repetier
Quoteo_lampe
Sounds like a new version of RADDS.
Which firmware does it work with?
by
svs072477
-
Developers
A new Board for 3D printer and arduino due from Russia.
http://ruramps4d.ru
The Board is already on sale and is shipped worldwide. Delivery is already included in the price.
Key board features:
Possibility to use TMC2130 in SPI mode without wires. The SPI bus is already connected to the drivers on the PCB. 12-26V DC power supply; Number of installed drivers for form factor Pololu — 6; The total
by
svs072477
-
Developers
A new Board for 3D printer and arduino due from Russia.
http://ruramps4d.ru
The Board is already on sale and is shipped worldwide. Delivery is already included in the price.
Key board features:
Possibility to use TMC2130 in SPI mode without wires. The SPI bus is already connected to the drivers on the PCB. 12-26V DC power supply; Number of installed drivers for form factor Pololu — 6; The total
by
svs072477
-
Experimental and Hobby
Quotedc42
If you want to try that, I suggest you look at the Duet WiFi schematic. You'll also need to make a few firmware changes, because although I prototyped the WiFi interface on a hacked Duet 085 two years ago, all the subsequent development has been done using the SAM4E processor. So some changes may be needed. Also the SPI bus on the Duet WiFi is dedicated to the ESP and I doubt that shari
by
svs072477
-
Experimental and Hobby
Quotedc42
To use an ESP8266 connected via serial only, ESPRINTER is the way to go. The ESP8266 support in RRF assumes a high speed SPI interface between the ESP8266 and the main processor.
ОК, аnd if I connect ESP8266-12 to SPI on Due, using CS_ETH, can I use the native RRF web interface?
by
svs072477
-
Experimental and Hobby
Quotedc42
The Pins_RADDS file defines two serial ports, of which the first is the USB port. So one of the real serial ports should work already. To get the other one working you would need to increase NUM_SERIAL_CHANNELS to 3 and define SERIAL_AUX2_DEVICE as Serial2.
AFAIK dcnewman hasn't done much work on his fork since I integrated it into mine, but I could be wrong.
Thanks, SERIAL_AUX2_DEVIC
by
svs072477
-
Experimental and Hobby
Quotedc42
By way of explanation, there is a bug in the SAM3X microcontroller chip. If you enable the ADC input to read the on-chip temperature sensor, port PB27 no longer works.
In the build of RepRapFirmware for Arduino Due + RADDS, we disable the CPU temperature monitoring facility for this reason.
Are you planning to support RepRapFirmware on your board too? If the pinout of your shield is t
by
svs072477
-
Experimental and Hobby
Quotedc42
By way of explanation, there is a bug in the SAM3X microcontroller chip. If you enable the ADC input to read the on-chip temperature sensor, port PB27 no longer works.
In the build of RepRapFirmware for Arduino Due + RADDS, we disable the CPU temperature monitoring facility for this reason.
Are you planning to support RepRapFirmware on your board too? If the pinout of your shield is t
by
svs072477
-
Experimental and Hobby
QuoteMagoKimbra
Yes my pleasure... Send me the file pin when you have finish your testing..
Ok, Thanks
by
svs072477
-
GCODE, Software e Firmware
Quotedc42
Does that firmware enable the CPU temperature sensor?
Yes the problem was in the mcu temperature sensor, Thanks
by
svs072477
-
Experimental and Hobby
QuoteMagoKimbra
Ok I fixed it try now with last commit..
Thank you. Another question: RUMAMPS4D has already begun to be sold in Russia, can you add it to the list of boards supported by MK4Doue. If so, what is required of me?
by
svs072477
-
GCODE, Software e Firmware
QuoteMagoKimbra
Test it with last dev please..
I find this:
...When the SAM3X8E's internal AD15 input is enabled to sample the chips internal temp sensor, the digital output capability of SAM3X8E pin PB27 is disabled (Due pin D13). More specifically, to internally route the analog signal from the internal mcu temp sensor to the internal AD15 input, the internal digital output line for PB27 is usu
by
svs072477
-
GCODE, Software e Firmware
Quotedc42
Does that firmware enable the CPU temperature sensor?
I don't know. How to verify this.
by
svs072477
-
Experimental and Hobby
Tehrmistor read 23C, when choosing a dummy thermistor (998), the hotend does not turn on either.
In repetier firmware and marlin 2.0 it work.
There is an assumption that pin 13 in MK4Duo is reserved for something, but under that I can not find
by
svs072477
-
Firmware - mainstream and related support
Hi,
I developed a new shield for arduino due RURAMPS4D.
http://3dtoday.ru/blogs/svs0724/ruramps4d-ramps-for-adruino-due-the-pilot-shipment-available-for-zack/
I tried different firmware, and on Mk4DUE 4.3.2 encountered a problem:
The HotEnd0, controlled from pin 13 arduino, will not turn on. On other firmware everything works.
Here is the pinout file of the board
Can anyone suggest what migh
by
svs072477
-
Firmware - mainstream and related support
Hi,
I developed a new shield for arduino due RURAMPS4D.
http://3dtoday.ru/blogs/svs0724/ruramps4d-ramps-for-adruino-due-the-pilot-shipment-available-for-zack/
I tried different firmware, and on Mk4DUE 4.3.2 encountered a problem:
The HotEnd0, controlled from pin 13 arduino, will not turn on. On other firmware everything works.
Here is the pinout file of the board
Can anyone suggest what migh
by
svs072477
-
Experimental and Hobby
Hi,
I developed a new shield for arduino due RURAMPS4D.
http://3dtoday.ru/blogs/svs0724/ruramps4d-ramps-for-adruino-due-the-pilot-shipment-available-for-zack/
I tried different firmware, and on Mk4DUE 4.3.2 encountered a problem:
The HotEnd0, controlled from pin 13 arduino, will not turn on. On other firmware everything works.
Here is the pinout file of the board
Can anyone suggest what mig
by
svs072477
-
GCODE, Software e Firmware