Welcome! Log In Create A New Profile

GCODE, Software e Firmware

Il codice è la genesi dei nostri oggetti da stampare.

Page 1 of 42 Pages: 12 3 4 5

Forum List New Topic RSS

	Views	Posts	Last Post
►►►► LINEE GUIDA E REGOLE PER UN USO CORRETTO DEL FORUM ◄◄◄◄ Da leggere! Segnalate ai moderatori le discussioni da chiudere - LE REGOLE VANNO LETTE E APPLICATE! by Gordie	2,686	1	03/09/2014 08:26AM Last Post by Gordie
Kisslicer Versione Pro by mdcompositi	52	2	06/20/2018 01:01PM Last Post by alil2096
Problema MK4DUO 4.3.6 con laser by whitedavil	220	21	06/20/2018 03:45AM Last Post by whitedavil
Aggiornare il firmware da remoto by Mr.Goblin	313	6	06/20/2018 12:56AM Last Post by whitedavil
firmware adatto al mio accrocchio (Pages: 1 2) by fabry22	517	44	06/19/2018 02:54PM Last Post by onekk
Regolare Z-probe in MK4duo V4.3.5 by Pinguto	52	3	06/15/2018 05:13PM Last Post by Pinguto
Auto Bel Levelling <- VS -> GT2560 by Pinguto	183	19	06/14/2018 06:08PM Last Post by Pinguto
MarlinKimbra e G29 by Pinguto	147	13	06/14/2018 05:59PM Last Post by Pinguto
Eeprom I2C su ultratronics by X(SAND)X	244	19	06/12/2018 04:21PM Last Post by beppexx80
Cr-10 Marlinkimbra autotune fallito. by Ohmmasters	129	20	06/12/2018 09:54AM Last Post by Ohmmasters
Kisslicer 1.6.3 release by Fabrap	145	3	06/11/2018 04:13AM Last Post by eavo
ventola PLA con configurazione EEB - MKS base_l by alil2096	73	14	06/10/2018 09:38AM Last Post by alil2096
Marlinkimbra CNC by roncoa	426	12	06/08/2018 01:18AM Last Post by atomino
Scan 3d by Tester	69	1	06/06/2018 05:34AM Last Post by Tester
Problema KM4duo 4.3.6 all'avvio della stampante (nemmeno lo splashscreen) by fabios	124	21	06/05/2018 07:54AM Last Post by fabios
Repetier-host V2.1.2 layer 0 e z-offset problemi by grattila	45	1	06/05/2018 04:41AM Last Post by grattila
velocità variabile da strato a strato (Pages: 1 2) by Enki	681	47	06/03/2018 05:21PM Last Post by iosonopersia
Ramps-fd+induino due by voodooo	107	9	06/03/2018 02:13PM Last Post by Dariuzzo
Marlinkimbra va modificato? by mga	101	8	06/01/2018 04:42AM Last Post by onekk
Errore PID tune by mga	57	3	05/31/2018 09:33AM Last Post by mga
Touch - Marlinkimbra by mga	176	16	05/29/2018 01:01PM Last Post by MagoKimbra
MarlinKimbra 4.3.6 e autobedlevel by thriller47	105	9	05/29/2018 04:02AM Last Post by onekk
MNK4duo e sicurezze di temperatura by onekk	66	3	05/25/2018 12:59PM Last Post by onekk
UBL e MK4duo by onekk	73	4	05/25/2018 12:56PM Last Post by onekk
Mk4duo 4.3.6 non mantiene set temperatura by whitedavil	146	11	05/23/2018 12:57PM Last Post by whitedavil
Stampa multicolore Repetier Host e Cura Engine by lexering1988	536	22	05/22/2018 08:37AM Last Post by immaginaecrea
Comando per spostare gli assi a delle coordinate precise by ilmagowalter	85	3	05/17/2018 01:47PM Last Post by ilmagowalter
problema autohome prusa i3 by giuseppe_reprap	108	4	05/16/2018 08:24AM Last Post by MagoKimbra
problema autotune pid piatto prusa i3 con marlin installato by giuseppe_reprap	58	2	05/16/2018 04:59AM Last Post by bilanciamist
Mk4duo 4.3.6 Ramps 1.4 + 3dtouch +tmc2130 spi configurazione by gigahertz77	136	4	05/13/2018 07:43AM Last Post by MagoKimbra
MK4duo - calibrazione ntc dell'hotend by onekk	241	21	05/12/2018 03:00PM Last Post by onekk

Page 1 of 42 Pages: 12 3 4 5

GCODE, Software e Firmware

firmware adatto al mio accrocchio (Pages: 1 2)

velocità variabile da strato a strato (Pages: 1 2)