Show all posts by user
Page 1 of 1 Pages: 1
Results 1 — 11 of 11
Hi all,
I got my hands on a ENC28J60 LAN ethernet module. I have a BTT SKR v1.3 and got the RRF working when connected to USB. Is there any way to Connect this module to the SKR now that software SPI is implemented. I don't use a LCD screen.
Thanks in advance for any info.
DocSolo
by
DocSolo
-
Firmware - experimental, borrowed, and future
Hi all,
Finally fixed my issue. I found on the marlin github an issue about slow bump with both MIN and MAX endstop assigned not working. On my printer I have a filament runout sensor connected to XMIN that was causing the issue. Commented out the line #define USE_XMIN_PLUG // Filament runout sensor and delta calibration now almost works. After running it, it looks like the bed is tilting low on
by
DocSolo
-
Firmware - Marlin
QuoteDust
why are you using mixed stepper drivers on delta towers ??
from your configuration.h
#define X_DRIVER_TYPE TMC2100
#define Y_DRIVER_TYPE TMC2100
#define Z_DRIVER_TYPE A4988
I'm not saying this is an issue, but it does seem an odd choice
Hi Dust,
I finally got my 3rd TMC2100. I'll leave the extruder with A4988 ubtil I find a better one.
by
DocSolo
-
Firmware - Marlin
It depends. I have a 240 mm bed and my rod arm length is 250 mm. When I move the effector past ±80 mm in any direction, the effector tilts I'd say for 0 to 10 degrees up on the far side. So I have my probing radius at 70 mm. But since I cannot do the delta calibration, I cannot print. Back when it was working, the hotend was starting prints about 2 mm above the bed. I searched the many forums to
by
DocSolo
-
Firmware - Marlin
Really sorry about that last comment. I'm very frustrated after 4 months of trying to get my printer actually printing. Naturally I do my own research before posting on any forums but so far, no cigar...
by
DocSolo
-
Firmware - Marlin
QuoteDocSolo
Hi all,
I'm having an issue trying to calibrare my homebuilt delta printer. I'm using BTT SKR v1.3 with latest Marlin 2.0 firmware. I am including a zip file containing the debug with S247 option and my config files. The way it works at the moment is G28 is partially working, as in: hit the 3 endstops but only does the slow bump on Y and Z axes. Sending the G33 homes the same way, g
by
DocSolo
-
Firmware - Marlin
Hi all,
I'm having an issue trying to calibrare my homebuilt delta printer. I'm using BTT SKR v1.3 with latest Marlin 2.0 firmware. I am including a zip file containing the debug with S247 option and my config files. The way it works at the moment is G28 is partially working, as in: hit the 3 endstops but only does the slow bump on Y and Z axes. Sending the G33 homes the same way, goes down abou
by
DocSolo
-
Firmware - Marlin
Hi all,
I have the same issue with a Micromake D1 effector using a microswitch using the hotend bumping the bed. I have the log of the debug leveling available if needed.
I remember that it worked a couple of months back but I don't take not of the version unfortunately. I have the latest Marlin firmware compiled. Basically I have an enlarged Micromake D1 printer with Skr V1.3 board.
Any help w
by
DocSolo
-
Firmware - Marlin
The store I do business with had only 1 TMC2100 left when I was there and the A4988 are from another old printer. Also I'm on a fixed income so I have to spread my purchases over time. I will get 2 more TMC2100. Second point, I cannot recall which version was working and am not familiar enough with github to find earlier builds. I did post a comment on the marlin github. TTYL.
by
DocSolo
-
Firmware - Marlin
Hi all, I have this issue after updating to the latest version. I checked forums for a solution but found nothing that work. I have a log of the auto-level debugging and config files that I include here . I checked the code but since I'm not good at programming, I did not see anything related. I am running Marlin on a BTT Skr V1.3, no hot bed, TMC2100 on X, A4988 on YZE. The Z-probe is a micro-s
by
DocSolo
-
Firmware - Marlin