bonjour à tous, j'ai poser le capteur de proximité sans soucis. il fonctionne très bien. j'ai fais quelques test pour vérifier le bon fonctionnement et me suis aperçu que le niveau 0 est variable. je m'explique : -------- Lancer Repetier-Host La buse est physiquement ~20mm au dessus du plateau M114 donne pour XYZ 0 j'exécute G90 G28 x, y G29 l'opération s'effectue normalement. Repeby taratata - RepRap Groupe d'Utilisateurs Francophone
merci, prob résoluby taratata - RepRap Groupe d'Utilisateurs Francophone
bonjour à tous Marlin RCBugFix "Default_version.h" #define SHORT_BUILD_VERSION "1.1.0-RC5" #define DETAILED_BUILD_VERSION "1.1.0-RC5 From Archive" #define STRING_DISTRIBUTION_DATE "2016-04-01 12:00" j'ai brancher la capteur de proximité LJC18A3 H Z/BX comme ceci Le fil jaune est brancher sur le PIN Signale min-Z Ramps1.4 J'ai bien une tension de 6.64v aux bornes (Jaune/Noir à droite de l'imby taratata - RepRap Groupe d'Utilisateurs Francophone
voici comment je fais 0 Power Supply ON TempRoom 0 - Thermistor 100k B3950 1 - Marlin configuration.h 2 ArduinoIDE Upload Marlin Firmware 3 - Start AutoTune PID 3 - Start AutoTune PID bis 4 - New Value PID 5 - Extruder is Cold 6 - Wrong Room Temperature 6 - Wrong Room Temperature bisby taratata - Reprappers
voici comment je mis prends 0 Power Supply ON TempRoom 0 - Thermistor 100k B3950 1 - Marlin configuration.h 2 ArduinoIDE Upload Marlin Firmware 3 - Start AutoTune PID 3 - Start AutoTune PID bis 4 - New Value PID 5 - Extruder is Cold 6 - Wrong Room Temperature 6 - Wrong Room Temperature bisby taratata - RepRap Groupe d'Utilisateurs Francophone
j'ai mesuré la tension (volt) sur les bornes T0 T1 et T2 --> 4.74v j'ai aussi testé la continuité (multimétre) entre les bornes 1, 3 et 5 --> OK comment puis je mesurer Ko entre les bornes 2, 4, 6? Normalement, la valeur doit être de 4.7Ko selon le schéma y a t'il d'autres mesures pour s'assurer de la fiabilité des PINS thermistors?by taratata - RepRap Groupe d'Utilisateurs Francophone
j'ai mesuré la tension (volt) sur les bornes T0 T1 et T2 --> 4.74v j'ai aussi testé la continuité (multimétre) entre les bornes 1, 3 et 5 --> OK comment puis je mesurer Ko entre les bornes 2, 4, 6? Normalement, la valeur doit être de 4.7Ko selon le schéma y a t'il d'autres mesures pour s'assurer de la fiabilité des PINS thermistors?by taratata - Reprappers
j'ai changé de thermistance et connecté uniquement l'extruder avec sa thermistance sur la ramps1.4. j'ai toujours cette écart de mesure de température au froid. la température ambiante est de 23°C (multimètre) alors que la mesure donnée par la thermistance indique 30°C l'alimentation est une ATX 12v v1 20A - 12v v2 20A de l'aide svp merciby taratata - RepRap Groupe d'Utilisateurs Francophone
I find that the temperature indicated by the thermistor extrude without power 12v transformer and only via USB, repetier-host shows at 27 ° C if I activate the 12v power and USB, the indicated temperature is 37 ° C! the thermistor is a 100k + - 5% B: 3950 + -1% on ID Marlin 13by taratata - Reprappers
je constate que la température indiquée par la thermistance de l'extruder, sans alimentation du transformateur 12v et uniquement via USB, repetier-host indique 27°C lors que si j'active le courant 12v et USB, la température indiquée est de 37°C! la thermistance est une 100k +- 5% B:3950 +-1% sur ID Marlin 13 une idéeby taratata - RepRap Groupe d'Utilisateurs Francophone
after using pid autotune, the thermistor of the extruder indicates a temperature of about 40 ° C instead of the ambient room temperature of 23 ° C. Yet the thermistor is a 100k 3950. I tested with MArlin's IDs 1-11 and 13. (sorry my english not well)by taratata - Reprappers
si je débranche uniquement la thermistance du BED, j'ai une mesure indiquée sous repetier host! bizzareby taratata - RepRap Groupe d'Utilisateurs Francophone
j'ai test la commande M303 E0 S220 C8 avec ID 11 et 13 mais la lecture de la température ambiante ne correspond pas à celle indiquée par le multimétre en mode TemP. d'après ce graphe (lu sur internet) il faut une stabilité que calculera Autotune PID. Mon extruder est isoler avec du Kapton voici les variation de l'extruder que j'obtiens est ce que la variable "#define PID_FUNCTIONAL_RANGE"by taratata - RepRap Groupe d'Utilisateurs Francophone
sur le site du vendeur, en pièce détachée, la thermistance correspond à celle-ci (d'apparence c'est la même) Prusia i3 M505 Melzi v2.0by taratata - RepRap Groupe d'Utilisateurs Francophone
merci pour ta réponse! j'ai deux solutions, soit je remonte la melzi ou je décompile le fichier HEXby taratata - RepRap Groupe d'Utilisateurs Francophone
Bonjour, je suis nouveau sur le forum. j'ai 52 ans et j'ai acquis une Prusa i3 M505 équipée avec un Melzi v2. n'arrivant pas à mettre à jour le firmware pour mettre un capteur LJC18A3 H Z _ BX. j'ai donc décider de la remplacer par une ramps 1.4 avec Marlin-1.1.0-RC3 . je n'ai pas rencontrer de problème majeur pour la partie de configuration des stepsitcks et moteur. Cette étape fonctionne trèsby taratata - RepRap Groupe d'Utilisateurs Francophone
Hello, I replace the Melzi RAMPS v2.0 1.4 I'm in the extruding and PID configuration phase. When connecting repetier sub-host, there is the line "Active Extrude: 0" entered 2 times. I do not toruve the solution .. anyone have a diee, please? here is MArlin #ifndef CONFIGURATION_H #define CONFIGURATION_H #include "boards.h" #include "macros.h" //=========================================by taratata - Reprappers
as tu solutionner ton problème?by taratata - RepRap Groupe d'Utilisateurs Francophone
j'ai le même soucis ... regarde mon ISP.PDF en fin de page... si l'un de nous trouve la solution, on communique svp d'après moi on peut toujours flasher la mezli mais il faut résoudre de l'identification de la carte et du port (celui de l'arduino normalement)by taratata - RepRap Groupe d'Utilisateurs Francophone
Hello everyone, I try the ISP connection mode with Arduino Uno equipped with ATmega328P The PDF file is the procedure that I have made in collecting information. --> you can find the ISP.PDF here (at the bottom of the page) Since the second test with "Sanguino / w ATMega1284p 8Mhz" ( Arduino TX and RX LEDs flash), the screen displays imp Simple square (cursor-type MSDOS) then Melzi LEDby taratata - Printing
thank you som much for your advice. can you explain me please, how to do for access to the firmware and upgarte it? I'm new with arduino and i think Mezli is not commun board. I need aduino hardware and arduino IDE for log to the Mezli and then, i setting the conguration.h file and i make the the upgrade? is irght? thank you in advance for your time... have good dayby taratata - General
the solution : check this PDF file : Avec un éditeur de texte, ouvrez le fichier "FTDiBus.INF" Section %USB\VID_0403&PID_6001.DeviceDesc%=FtdiBus.NT,USB\VID_0403&PID_6001 %USB\VID_0403&PID_6010&MI_00.DeviceDesc%=FtdiBus.NT,USB\VID_0403&PID_6010&MI_00 %USB\VID_0403&PID_6010&MI_01.DeviceDesc%=FtdiBus.NT,USB\VID_0403&PID_6010&MI_01 Voici les nouvellesby taratata - General
HI everyone, I have more access to the 3D printer. I uninstalled and reinstalled the drivers , still the same message. I also installed the printer on two other computer even worries. here is the message: thank you for you solutions if ...by taratata - General
Hello everyone, I hesitate a lot of 3 cards " 1.4 Ramps " " MegaTronics 2 or 3" " Mezli 2.0". Mainly it is the management of nb extrude which vary by model . I want to develop a printer on the best way for the thermal baths cushion . Since I know nothing about the matter, I ask myself the following question: The type of firmware? most flexible parameterization ? Ease of access to the flash ?by taratata - General
Hello everyone I acquired this IMP Hesine 3D RepRap Prusa i3 - M- 505 here I have a problem with the Y axis I noticed that the two needle bearings are housed on the right guide pin ( on the timeline, are right on the axis when faced IMP ) while the " Limited Switch Y" is placed on the opposite axis (left). So I ask the two needle bearings on the left axis . For both situations , with " Repetiby taratata - General