Hatte mich vor nem halben Jahr auch mal danach umgeschaut, aber nichts gefunden, Scheint in Deutschland nicht verkauft zu werden. Hast du den von BfB? Dann kvon Tobias Fleig - Altes Forum
Hmm welche Karte meinst du? Auf der "World RepRap Map" von der Startseite seh ich keinen in Mannheim. Ausserdem, gibt esvon Tobias Fleig - Schwarzes Brett
Reprap software params are listed here:von Tobias Fleig - General
There is a config file named reprap.properties - it's a normal text file, so open it e.g with the Editor, search for Port(name)=/dev/ttyS0 and change it to Port(name)=COM1 I'm using Linux so I don't know where you can find this file on windows, maybe in the reprap-host folder or just search for it...von Tobias Fleig - RepRap Host
I know but it isn't that easy, the BfB Extruder design is different, the heater barrel just touches the PTFE, but the parts aren't screwed together so the HDPE always finds a way through the half-molten PTFEvon Tobias Fleig - Plastic Extruder Working Group
1- Use heatsinks on the pwm transistors - they get really hot 2- Maybe something with your temp-sensor is wrong, i had no problems heating up the BfB barrel up to 230 C 3- I'm not sure, but if this is PTFE-smoke then it is dangerous! PTFE is stable up to 250-300 C --> maybe (re-)calibrate your sensor manually --> And last but not least - the pressure problem I tried the following thingsvon Tobias Fleig - Plastic Extruder Working Group
I had problems with two of my stepperboards, too. The problem was that I set them to Slave - without connection the sync-lines. So make sure all the Master/Slave jumpers are set to Master - and don't connect the sync-lines, you don't need them...von Tobias Fleig - Controllers
Yeah that's it, reprap moves now, thanksvon Tobias Fleig - RepRap Host
I'm using Single_Arduino_SNAP.pde - This is the right one for a normal single arduino reprap, isn't it?von Tobias Fleig - RepRap Host
Question maybe sounds a bit stupid, but I can't get my reprap to print... The exerciser-tools are working, but when I open an STL-file and click "Build" I just see this stupid build simulation, my RepRap does nothing... I'm using Arduino firmware 1.3 and reprap-host 0.9, but I also tried 1.2 and 0.8.3 - same result Have I just forgot something or is this a known arduino-bug?von Tobias Fleig - RepRap Host
Hmm ist an der Grenze, ist bei den Steckern/Leisten nicht die maximale Belastbarkeit angegeben?von Tobias Fleig - Altes Forum
3 pin header: PSK 254/3W 3 pin housing: PSS 254/3G Die .156" Dinger gibts bei Reichelt nicht, ich hab die aber auch sonst nirgendwo gefunden. Ich werd bei mir halt die Motoren irgendwie anderst anschlievon Tobias Fleig - Altes Forum
This the same story as the one with the Z Pulley, isn't it? I think there is only one part, a combined pulley + coupling, similar to the one on the Z-axis...von Tobias Fleig - Wanted
Ich glaube, wenn du die Schrittmotoren mit dem Arduino ansteueren willst, brauchst du beide Chips, ein Computer hat genug Rechenpower und ports, da knn man den Controller-Chip locker weglassen, aber beim Arduino ist das alles etwas begrenzter --> Das wvon Tobias Fleig - Altes Forum
Hi Tuchs! Das siehst du richtig, der Extruderkopf wiegt nicht viel undvon Tobias Fleig - Altes Forum
Arduino gibt derzeit in Deutschland nur bei Genaue Bezeichnung: "Arduino Diecimila Fertigboard mit Usb" Falls du ohnehin vorhattest bei RRRF zu bestellen, kannst es da mitbestellen. Rollen und Riemen z. B bei , da ist aber die Auswahl nicht so toll, besser ist die z.B. beivon Tobias Fleig - Altes Forum
Naja, so schnell geht das nicht. 1. Wir es noch einige Zeit dauern, bis mein RepRap wirklich vernvon Tobias Fleig - Altes Forum
Die Motoren von Keling haben (mit Porto) 76,34von Tobias Fleig - Altes Forum
Hi Daniel, mein RepRap Darwin steht kurz vor der Fertigstellung (nur der Extruder fehlt noch). Ich hab ein Grovon Tobias Fleig - Altes Forum
Blender is a real powerful tool, but it's very different from other 3D design tools, so its a bit tricky to get what you want. But if you learned how to use Blender, you'll never use something else! There's no problem designing models for RepRap with Blender, I think. One unit on the default grid appears to be 1 mm. Just export your model as STL and load it into the RepRap-Software. These are tvon Tobias Fleig - 3D Design tools
Hi all, i'm located in the Black Forest (Schwarzwald) / Germany i've got a half-finished RepRap here and i'm waiting for the stepper motors from keling... Tobiasvon Tobias Fleig - Schwarzes Brett