Ich habe momentan leider nur einen analogen messschieber, aber dessen werte stimmen mit den theoretischen im gcode überein, so gut man das auf 1/20mm ablesen kann. ich möchte gerne so gut drucken können, dass man keine "rillen" in zb einer gehäusewand mehr sieht, oder möglichst kleine. habe eben mal ein raspberry gehäuse angefangen, das sieht schon sehr schön aus und ich habe 0.25mm layer eingevon muelli - Allgemeines
I also thought about that option.... but I had several Mendel90 lock-ups while printing larger parts over the USB connection. (I must admit, I use a 5m Cable *g*) DId you have any trouble printing with the raspberry and octoprint? It looks quite....old fashioned, I have to say. I would really like to have a touch screen with pronterface on the Pi, but that is quite expensive PS: Do you have avon muelli - Mendel90
Hi, does someone have a Mendel90 equipped with a LCD to have it operate in stand-alone mode? The Panelou seems to need major firmware mods and I do not know, if this is possible with nopheads fork of marlin. Thannks!von muelli - Mendel90
Ich habe jetzt eine 0.5mm thin wall gedruckt mit gemessenen 0.55mm ich denke das kann man akzeptieren, oder?von muelli - Allgemeines
Danke, schau ich mir mal alles an!von muelli - Allgemeines
Hallo zusammen, ich bin aktuell noch beim kalibrieren meines Mendel90. Dazu habe ich jetzt die entsprechende Wiki Seite durchgeackert und frage mich, wie ich beurteilen soll, ob die Testobjekte auch gut aussehen. Das ist ja alles relativ. Gibt es eine Ansichtsseite mit Bildern (Super, gut, OK, schlecht, ...)? Beim 3mm Rechteck war das noch recht gut zu beurteilen, aber bei der 0.5mm thin wall svon muelli - Allgemeines
danke organisiere mir nun ne uhr! wie lange sollte denn der schaft sein? ich habe bisher nur uhren mit 10mm schaft gesehen, es gibt aber verlängerungen zum anschrauben....von muelli - Offtopic
that is what is starting wars. expecting things ;-) always make it clear.von muelli - Mendel90
bastard Wrote: > Und zum > Nivellieren des Druckbetts mit einer Meßuhr hab > ich den dafür nötigen Halter gedruckt. Hi, wo gibt es denn diesen Halter zum download? Momentan fummele ich mit Augenmaß und Blatt Papier rum Danke!von muelli - Offtopic
aaaah now I understand thanks! I measured and had 22.4mm left, so it extruded not enough...von muelli - Mendel90
about debris on the nozzle.... how can i prevent the filament from dripping out during heating up the hot end while waiting for the print?von muelli - Mendel90
the screws with the springs come out at the other end. the go through. i think you should screw them in until the ende of the screw juuuuust comes out, lines up with the holes. hard to explain for a non.native english speakervon muelli - Mendel90
Well, we know this is in the manual, but the question is, how do you adapt the info in the manual: "Multiply the E_STEPS_PER_MM in the firmware by 100 / actual extrusion and reload it" to the formula in the config header file #define E_STEPS_PER_MM ((3200 * 39.0)/(11.0 * 6.75 * 3.142)) where goes your measurement into which place?von muelli - Mendel90
Same problems here with at least point 26. No idea how to do extruder calibration.von muelli - Mendel90
Hello again, after the problems yesterday evening were solved, now I have another one. After printing the android sample once, the extruder stopped printing filament. If I heat it up manually in pronterface and manually extrude, everything works. But when I try to print the sample again or something else, nothing comes out of the extruder. I can see the gears of the extruder motor move. Heatingvon muelli - Mendel90
OK, I checked the manual again and found the hint on compiling the firmware. I replaced the 203mm with 205mm and now it is printing )von muelli - Mendel90
I did it all again, adjusted the nuts on the threaded rods until everything was fine, could move up the Z axis, and down again but when I started the print, the hot end again stopped 3-4mm in the air. could that be a problem with the android example? when I then reset the printer, I cannot go the whole way down to the hotbead. It seems to have "forgotten" it was there.... edit: could it be possvon muelli - Mendel90
ok, thanks for the info about problem 2 yes everything is as tight as it should be, checked it. I re-calibrated again, startet the android load and once again, the hot end stops 3-4mm above the glas plate and starts printing into the air....von muelli - Mendel90
Hi, I have two problems: 1. after i finished my mendel90 built I tried to calibrate it. I cannot seem to get it right. I move the bed to the front and the extruder to the middle and calibrate back middle, left and right points so that just a sheet of paper passes the hot end. then I move to the front and do the same but by moving the bed as mentioned in the manual. everything looks good but whevon muelli - Mendel90
Ich möchte Gehäuse und ähnliches für Prototypen drucken und hatte bisher nur während des Studiums mal ganz kurz was mit 3Dmax gemacht, das ist jedoch schon 10 Jahre her. Habe mir also mal DesignSpark Mechanical installiert und bin sofort damit zurecht gekommen! Komplizierteres wie Gewinde, Zahnräder und ähnliches habe ich noch nicht probiert, weiss auch nicht ob das geht, aber für einfache Gehäusvon muelli - Software
Nochmals danke Dann bin ich jetzt soweit erleuchtet. Bist Du mit Deinem Mendel90 schon fertig? Kannst Du dich schon irgendwie dazu äußern oder mal das eine oder andere Exponat präsentieren? Ich habe bisher in einem anderen THread eine handvoll Bilder gesehen, aber das was von rel. weit weg und ich konnte mir noch keinen Eindruck von den Möglichkeiten machen. Das wäre super wenn Du mal was anhänvon muelli - Allgemeines
Danke für die Info, das hat mir schon weitergeholfen! Es ist gar nicht so einfach, sich durch den Begriffsdschungel zu wuseln zu Beginn Zwei allgemeine Frage noch: 1. Ist es wahr, dass mit 1.75mm Filament und Hotend mit kleiner Öffnung die Details besser werden? Wenn ja, wieso benutzt nicht jeder diese Kombination? Ich kann mir denken, dass der Druck dann langsamer wird, aber so dramatsich sovon muelli - Allgemeines
Hallo zusammen, ich hänge mich mit meiner Frage einfach mal hier dran, da hier ja schon der Mendel90 besprochen wurde und ich mich für den Bausatz interessiere. Ich möchte jedoch zukünftig unabhangig sein und frage mich nun, ob es einfach möglich ist, den Extruder zu tauschen, zB vom 3mm auf 1.75mm oder von direct auf bowden. Dazu habe ich mich jetzt geraume Zeit hier durchgeklickt und nicht wivon muelli - Allgemeines