Show all posts by user
Printing issues ...
Page 1 of 1 Pages: 1
Results 1 — 27 of 27
So I have changed the ramps yet again and still nothing. Im thinking it it in the set up now. maybe in the PID settings?
by
gilsah
-
Reprappers
The resistance in both beds is the same 1.5, Also I was incorrect about the power supply feeding power I have 15v and 12 amp.
by
gilsah
-
Reprappers
After changing heat bed, the ramps, and arduino all I get now is the LED to flash on very quick every other second. I am using a 15 volt 6 amp wall wort for power on the heat bed side (right) I have power after the fuses both big and smaller one. Im at a total loss could it be the mossfit? and how do you check them?
The bed did work at one point in time but not very well. It would take forever
by
gilsah
-
Reprappers
That's what I was thinking but I could not find it in print anywhere!!!! Thank you so much!!
by
gilsah
-
Reprappers
my new configuration.h file
by
gilsah
-
General
OK I've tried M303 E-1 C8 S85 and when it hit 105 it failed saying it was too high again.
by
gilsah
-
General
PID Failed ! Temp too high
by
gilsah
-
General
What temp is youre extruder set to? Mine looks like that when it is too high
by
gilsah
-
Printing
I cant find where to connect the switch for auto bed leveling. Can any one help?
by
gilsah
-
Reprappers
OK I have finally Replaced the ramps and arduino and also the heat bead. Still the same issue.....I have also been trying to auto tune the PID for the bed. it failed as soon as the temp hits 110 but my max temp for the bed is set to 150? So I don't know why it will not pass the 110 mark. This is the code I type in to run the auto tune M303 E-1 C8 S90 I know Im missing something just don't know wh
by
gilsah
-
General
Thank you so much. I kind of figured that but thought it would be better to ask
by
gilsah
-
General
Can any one explain what the (*8) and (*1.1) do in this line
#define DEFAULT_AXIS_STEPS_PER_UNIT {78.7402,78.7402,1520.0*8/3,515*1.1} // default steps per unit for Ultimaker
and isn't it say the first # of 78.7402 the motor steps for x to go 1 mm?
by
gilsah
-
General
Any one have any idea what I am doing wrong? I've looked for the last 3 days online to find a clue on what to do but no luck.
Thanks in advance.
by
gilsah
-
Printing
Well I found out I have a bad arduino!! The analog pins do not read correctly. I have anew one on order but wow did I learn figuring that out. Thank you all for the help.
by
gilsah
-
General
I did the calibration on the filament. So when I extrude 20 mm that's the amount of filament it uses.
by
gilsah
-
Printing
Ok I think I've lost 1/2 my hair today and the rest turned gray!! So I switched to mirlin firmware. And repetier after all day calibrating and running tests I think I figured out that it don't matter if you are extruding 20mm when you call for 20mm it's how the print looks. So while trying to change the settings I got a heat bed error saying it was over temp! Now it will not show a temp at all j
by
gilsah
-
General
Ok so I just ran a 5mm wall test cube and it is 6mm thick? what do I do now?
by
gilsah
-
Printing
I will look more tomorrow but the smaller fuse is warm. The bigger one is not
by
gilsah
-
General
ok here is the configuration.h file
by
gilsah
-
General
Lol I will repost configuration.h when I get home. It was way past my bed time.
As for the wiring I have checked over and over. It's wired up right next to the power. And from thinking about it I don't remember ever seeing a LED for the hot end coming on or off.
by
gilsah
-
General
and looking in the wiki I thought sprinter was the newest firmware?
by
gilsah
-
General
yes 2 and 3 go to ground.
by
gilsah
-
General
You mean that you see no temperature change for 5 minutes after you send the command for the bed to heat? Correct. There is no voltage going to the bed
How can they blink at the same time but not blink in the same pattern? It's always the same time just not always the same pattern. As in the times it blinks changes every so often.
Do you mean that the bed eventually heats up to the proper tem
by
gilsah
-
General
D8 on the pos. and neg.
D9 is fan
D10 is hotend heater
by
gilsah
-
General
Hello all! I'm having heat bead issues. It takes about 5 min before it will start to heat. The LED on the board and LED #4 on ramps blink at the same time but not always in the same pattern. Also it will drop about 30 degrees before it starts to heat up again? I have good power supply so I'm thinking it might be in sprinter. Any ideas would be great.
by
gilsah
-
General