For host estimated time it is in printer settings (Add to comp. time) which increases the time prediction. This is an empirical solution that greatly depends on your firmware settings and slicer method. A more relieable solution is the repetier-server time prediction which takes accelerations into account if configured correctly.by repetier - Repetier
While homing host shows what you have said in host config. After homing firmware sends real coordinates which seems to be 120. Check eeprom settings zlength value. I guess there you have 120. As a result doing G1 Z0 will stop quite high.by repetier - Repetier
Never seen this. You mean the 3d view tab is active but does not update to showit? Does the temperature graph still update every second or is it just the old image and it is not painting the 3d view again? Please open log (toggle log) and check for OpenGL version reportet and error messages. I think your OpenGL settings do not match the expectations (OpenGL 1.5 as minimum version for VBOs) The gby repetier - Repetier
I'd say it is a bug. In code to change cases i compared if it is between z and z and not a - z. In some cases it does not understand server will send gcode unaltered so then it is up to the firmware to fix the case error. Since some commands contain real lower chars like M117 a general uppercase of the string is not a solution. But with the fixed version it should generally work then.by repetier - Repetier
In config tool it is in general tab but only visible for delta printer. There see headline "Z-correction (distortion correction)". I guess I should add a test to disable it on non deltas in any case.by repetier - Repetier
Distortion measurement requires a zprobe, see function definition here #if FEATURE_Z_PROBE float Printer::runZProbe(bool first,bool last,uint8_t repeat,bool runStartScript) so I guess you have FEATURE_Z_PROBE not enabled but distortion correction. I will add a compile error stating that more clearly in the next update.by repetier - Repetier
It simply says you are using pin 54 and your selected processor does not have pin 54. So you have either selected the wrong motherboard or set a wrong pin number for X_STEP_PIN.by repetier - Repetier
Other software increment in steps of 1 and no one questions. Version umber is just a decision and we wanted to show that the new server inclusion is a big step, so we wanted to show it also in a version number. That's why we called it 1.5.by repetier - Repetier
Thanks for the fast feedback. In my test environment it worked but in production environment I was also able to get the error. Should now be fixed in 1.5.2.by repetier - Repetier
Changes are shown when you click "Check updates" in host and there is a new version. It will then show which and what is new so you can decide how urgent update is. Flow slider is hidden in easy mode. Bed slider only appears if firmware reports temperatures for bed. If not it will disappear after connect.by repetier - Repetier
Before you ask - I guess we will upgrade to new CuraEngine once we find a way to make it work with our configuration and understand all the changes.by repetier - Repetier
Last before they made everything incompatible with a completely new configuration and communication setup. So end april was the last commit included.by repetier - Repetier
Please check log for any messages that help.by repetier - Repetier
It is a old problem coming back. Slic3r has problems reading the slic3r file from non ascii file path. We have just released 1.5.1 where we set working directory as start directory so we could omit all the path and slic3r is happy again. So please update and it should work.by repetier - Repetier
You see it always in the update message. Here for completeness: Version 1.5.1 * Fixed print problems when exceeding line 65535 * Fixed slic3r issue with non ascii user names. Version 1.5.0 * Connector for Repetier-Server. * Support of repetier binary protocol V3. * New CuraEngine version. * Slic3r 1.2.9a included. * New EEPROM handler for Repetier-Firmware. * Better support for high DPI displayby repetier - Repetier
These are many questions and not very much informations, so I think I did not get all problems. First server connects automatically with printer if activated. If that happens no other program should/can connect with printer until server printer is deactivated. Normally no problem - after all taht is why the host has the server connector so you do not connect directly with th ehost any more - alwby repetier - Repetier
Most important is to use the right ip. On local you can use 127.0.0.1 or localhost but that means "this computer" and will not work on the second computer. There you need the ip the computer has in network. In command line tool (Win+R cmd) you can enter ipconfig to see them all. It also shows mac address so you can tell your router to always give it the same ip.by repetier - Repetier
There is no reason why it should not work on 1.5 as well. That part hasn't changed and just used it with success, so it works.by repetier - Repetier
You better reread your image. That is the infill density of support not the one for normal infill. Normal infill can not be set in that settings. It is only available in the right tab with the slider called "infill density" where you also start the slice.by repetier - Repetier
Assuming the sensor it self is ok, 359 would indikate the wrong sensor type.It might be a thermocouple or a thermistor. Both have very different characteristics, so you have probably set the wrong type.by repetier - Repetier
What is your value of the infill density in the CuraEngine tab when you slice? With 0 you would get no infill.by repetier - Repetier
Exactly. In the other thread for a due with similar problem the fix alraedy worked.by repetier - Repetier
BOARD_RAMPS_13_EEB is a Marlin configuration option. I don't know how Marlin works in detail. I was assuming Repetier-Firmware since this is the repetier forum. In repetier you could have a cooling fan that enables when heater is on and a heating element. Should work.by repetier - Repetier
That is not implemented. A solution would be to say you have 2 extruder and give the second extruder the T2 thermistor. Then host will also show it as E2 Temperature. Just remember to not print with second extruder :-)by repetier - Repetier
Just found a possible issue with M42. Fixed this in 0.92.3 and hope it helps.by repetier - Repetier
Screenshot is definitively not from Repetier-Firmware so I can not say anything about this problem.by repetier - Repetier
What I do not understand is "Z probe out bed" because the firmware does not have this error message. Is this really what you get or did you change the message? Or did you get this with Marlin? Homing does not do any z probing stuff, so you should never get a z probe message while homing. G30 could do but that is not z homing. I also think you ruled firmwares as M211 is not implemented in Repetiby repetier - Repetier
What does the log say. I checked the code and if it does not set the pin you get always a error message. There is one command in M42 that could make trouble analogWrite(pin_number, com->S); This could activate PWM with a used timer. So you might remove it so that only the digital write stays. (Commands.cpp line 1470 in latest 0.92.3) I also think it is not in sensitive pins.by repetier - Repetier
I don't think so. You can use Repetier-Server. There you can have any number you like and also give the scripts a name so they are easier to find. With the new 1.5 host you can also use it over the host also then you can not access the server scripts.by repetier - Repetier
Install Repetier-Host and connect with cable setting right baud rate. Host has a log option (easy mode off)by repetier - Repetier