Instelling in slicer wat jouw heatbed afmetingen zijn en waar het stuk staat.von CharlieSteurbaut - Dutch User Group - Archive
We have some new LCD screens in our range. And we have a lot of prusa i3 back in stock!von CharlieSteurbaut - For Sale
Hello, Thats caused by the threaded z rods. What the printer you are using?von CharlieSteurbaut - General
We added some videos of printing prusa i3 printer, check them out!von CharlieSteurbaut - For Sale
Waarom geen DIY printer? Die kunnen wel ABS printen en dergelijke.von CharlieSteurbaut - Dutch User Group - Archive
Also here an anounce to our new Prusa i3 printer. Check our webshop for more info!von CharlieSteurbaut - For Sale
Hallo, Bedankt voor jouw reactie! Ja als je misschien alles zelf sourced dan kan je het iets goedkoper vinden maar het risico dat er iets tekort is of iets niet past is groter dan dat je de kit koopt. En de firmware en al de nodige software met handleiding is allemaal inbegrepen dus je bent na een paar uur klaar en up and running. En de shipping is ongeveer een dag of 2-3 naar Nederland.von CharlieSteurbaut - Dutch User Group - Archive
Hallo allemaal, Ik laat hier ook eventjes weten dat sinds vandaag er een prusa i3 kit in ons gamma aanwezig is. Voor de mensen die interesse hebben: Foto's, films en handleidingen komen online in de loop van volgende week.von CharlieSteurbaut - Dutch User Group - Archive
Hello, I'm proud to announce that we have a Full Prusa i3 kit - METRIC in our range from now on. More info and videos will be available next week. The first kits will be shipped from 2nd of September. The kit can be found here: If you have any questions or remarks, don't hesitate to contact us!von CharlieSteurbaut - For Sale
Hallo, Op mijn webshop bij links staat mijn dropbox endaar staat ook heel wat uitgelegd ivm de software en dergelijke misschien ben je daar iets mee?von CharlieSteurbaut - Dutch User Group - Archive
We are back from vaction so we are up and running again use the coupon code to get a free SD card reader!von CharlieSteurbaut - For Sale
If you buy for 50 euro on our shop you can use the following coupon to get a free SDRamps! Coupon Code: CHARLIES3DT2013002von CharlieSteurbaut - For Sale
Some Original Prusa i3 alu frames in black an blue available now!von CharlieSteurbaut - For Sale
Hello, Are you using slic3r to slicing the parts? Set the begin temp in slicer to 0 Then you can control the temp in printrun and then you can start when you want normaly.von CharlieSteurbaut - Reprappers
Hallo, Kijk eens op mijn webshop naar de full prusa mendel kit, onderaan staat een link naar mijn dropbox met files en info over de firmware. Gebruik ook de arduino die hier instaat. Dit is een 'oude' versie en deze gaat meestal wel in verifieren enzo.von CharlieSteurbaut - Dutch User Group - Archive
Some full kits are available again. And the prusa i3 kit will be online in 2-3 weeks!von CharlieSteurbaut - For Sale
Hard to tell. The hottend is clotched up probably. Is it mounted correctly.von CharlieSteurbaut - General
That bolt is not so good this can be the problem.von CharlieSteurbaut - General
What hotend are you using?von CharlieSteurbaut - General
Do you have a photograph of your bolt?von CharlieSteurbaut - General
Watch out for the Jhead hotends that are not Original ones. The link is not a Original one.von CharlieSteurbaut - General Mendel Topics
Draai jouw plug van de motor gewoon om. Dan zal deze wel in de juiste richting extruderen.von CharlieSteurbaut - Dutch User Group - Archive
Ik zou gewoon zorgen dat je onder jouw bed enige vorm van isolatie plaatst. En normaal moet het dan wel goed zijn.von CharlieSteurbaut - Dutch User Group - Archive
Ik print met 6 printers op dit moment op 12 volt en deze bekomen een temp van 110 graden. Dus ik zie het probleem niet echt?von CharlieSteurbaut - Dutch User Group - Archive
New batch of filament available again!von CharlieSteurbaut - For Sale
Ik heb er enkele: www.charlies3dtechnologies.euvon CharlieSteurbaut - Dutch User Group - Archive
Misschien kan ik jou helpen met een aantal stukken zoals lagers en motoren en heatbeds en dergelijke: www.charlies3dtechnologies.eu stuur me maar een mailtje als je nog vragen hebt?von CharlieSteurbaut - Dutch User Group - Archive
We have a Raibow pack of PLA and ABS filament.von CharlieSteurbaut - For Sale
The full prusa kits are back in stock!von CharlieSteurbaut - For Sale