Hello, I have a problem that i couldn't google out so i thought you guys might help. I've built Prusa i2 and it was working fine. Few complete prints and lots of trashed ones like every begginer have. Once it shut off (power supply switched off) middle print and i started searcching what might cause the problem. Since it's custom made power supply on CODEGEN 300W ATX 2.03(P4) MODEL:250XA i thby Gogolian - General
I would try decreasing temperature a little bit and/or generate some support material?by Gogolian - Printing
Hi, I just recently finished building mendel prusa i2. After a week of figuring out temperatures/configurations i started printing (today! finally!) However i came across this weird "gap" problem. Here's the photo: What could be making this? How to avoid it?by Gogolian - Printing
Hi, I'm at finish building my first printer (prusa i2) The last problem i have and i have no idea how to tackle is heatbed. Connected to D8 at ramps 1.4 it heats extreamly slow, or none at all (after 5 min waiting it's still cold, you can touch it with fingers, after 10 minutes it get just little bit warmish) Trying to locate the problem i temporarely switched it with hot end. Now hot end getby Gogolian - General
And what exactly to change here? #include "thermistortables.h" #define X_STEP_PIN 54 #define X_DIR_PIN 55 #define X_ENABLE_PIN 38 #define X_MIN_PIN 3 #define X_MAX_PIN 2 #define Y_STEP_PIN 60 #define Y_DIR_PIN 61 #define Y_ENABLE_PIN 56 #define Y_MIN_PIN 14 #define Y_MAX_PIN 15 #define Z_STEP_PIN 46 #by Gogolian - Reprappers
Hi, quick Question. I got Ramps + Adurino + Stepper motor drivers I also got motors today, but i'm still missing heater board. Can i test Ramps with this code: WITHOUT heater board connected? I've seen this guy: So it must be possible.by Gogolian - Reprappers
I'm not quite sure what you mean by the dampener (english is not my main language) Do you mean those metal parts on top? And i found this: I think i'll give it a tryby Gogolian - Reprappers
Hi! I just got these motors: i got ramps 1.4 which have 4 outputs per motor. How can i check which of those wires i have to use and what order should i connect them?by Gogolian - Reprappers
Thanks a lot Now i'll have 2 more bearingsby Gogolian - Reprappers
Hi, I puchcased printed parts for, i belive, mendel pursa and everything seems to be fine EXCEPT THOSE: Can anybody tell me what are they for?by Gogolian - Reprappers
Hello, I'm picking parts for my first reprap (mendel). I already ordered RAMPS 1.4 Now i see that in my country original stepper motors are quite expensive, but they are selling used ones (strapped from some other electronics) as well. Will this: SHINANO KENSHI STP-43D3013, or this JAPAN SERVO TYPE KH42JM2B247 wokr with RAMPS 1.4? They are 5-6 times cheaper, that's why i'm considering this. Alteby Gogolian - Reprappers
Even if i still don't have electronics? Just the plastic parts? Tomorrow i'm going to go buy rods, and i tought if i may do some modifications to get newest extruder/electronics to work it would be worth a shot. So which model does THIS extruder works with? Or maybe you'll give me some advice which extruder/ electronics i should use for my first printer?by Gogolian - Reprappers
Hello, I got printed parts For Mendel Pursa, the same as shown in this guide: I want to follow it to build my first RepRap, but i wanted to change extruder to this one: Do you have any clues if this will work? Do i need different electronics for this one?by Gogolian - Reprappers