My printer makes a squeezing sound on the motors and only x axis moves and the motor is extremely hot. I used the Prussia Mendel_i3 marlin firmware early "Marlin firmware used for Prusa i3 Hephestos - modified for Prusa i3 Rework" but it accept the job heats up, and when it about to start it stops and cools down. Now i installed another version "for a Geeetech i3 X: " and after i install when i tby Rasyoni - Printing
My printer makes a squeezing sound on the motors and only x axis moves and the motor is extremely hot. I used the Prussia Mendel_i3 marlin firmware early "Marlin firmware used for Prusa i3 Hephestos - modified for Prusa i3 Rework" but it accept the job heats up, and when it about to start it stops and cools down. Now i installed another version "for a Geeetech i3 X: " and after i install when i tby Rasyoni - Printing
Dear All, I was printing well for a while but now i saw some weird effects on my print object, which i attached the picture. Also pla are coming out from the top of the nozzle holderby Rasyoni - Reprappers
When i send the print job it accepts all the positions go to home Heat bed heating ok Nozzel heats ok But When it is ready the axis moves to the middle and to jogged and stops and the nozzle heat goes off and the printer freezes what would be the cause. No error message shown nothing but the nozzle cools off and i noticed one red light is blinking when it tries to print as it joggs. any Ideaby Rasyoni - Reprappers
Dear all i just gat a new (replacment) arduno board and it works well except when i tried to heat the nozzel the bed heat not the nozel and it stops by saying err፡max temp reached what could be the cause. I use both prontorface & repeaterhost.by Rasyoni - Reprappers
Thanks All. Finally I managed to print my first gear. @ Dust I will never forget your help it meas a lot. Regards One question tho: i printed my gear using repeaterhost and prontorface but the print quality is a bit poor even if i make the infill 100%. I attached the Pictures. Is there good way to get a smooth surface and know what type of print setting i need to use for different types of modelby Rasyoni - Prusa i3 and variants
Thanks a lot now i managed to install. Thanks. But now it says Err: MINTEMP Also Attached a picture.by Rasyoni - Prusa i3 and variants
K I change the PC and now the error changed I have attached the error message. Thanks Allby Rasyoni - Prusa i3 and variants
@Dust thanks. But when i tried to install the firmware i get this error message. Arduino: 1.8.3 (Windows 10), Board: "Sanguino, ATmega1284 or ATmega1284P (16 MHz)" In file included from sketch\SdFile.h:27:0, from sketch\cardreader.h:8, from sketch\Marlin_main.cpp:44: SdBaseFile.h:38: error: using typedef-name 'fpos_t' after 'struct' struct fpos_t { ^ Iby Rasyoni - Prusa i3 and variants
K my x axis limit switch is working now but the problem of himing z axis is because when i home it both x and y are at tge max corner ao when z axis desends downward and it gat thia 'optical senaor' as both at the corners it goes all the way down trying to break the bed. I attached the pic also. Thanks all.by Rasyoni - Prusa i3 and variants
I have bought a new board and try to auto level it and the printer y axis works fine but x axis moves towards the limit switch and don't stop. Z axis comes to the corner and wont stop b/c the optical sensor is suspending freely and nothing there to block it. Finally i cant get any driver to connect it to my PC (Windows 10). Highly Appreciated your help.by Rasyoni - Prusa i3 and variants
Gat U but my pronterface is not working because of the USB cable driver is not working and i tried FTDrivers but it cant connect it. I use windows 10. Also there is one PIn for x limit.by Rasyoni - Reprappers
Gat u. But in the mean time help me out with the tronxy. Till i get the board needed. Waiting your response. Thanks a lotby Rasyoni - Reprappers
Thanks Dust! will order but if I keep the same settings will it destroy the second one, Just asking if i need to change some thing. Ok in the mean time I have a new tronxy and the board was toasted before i assemble it but now i get yesterday a new board but it comes with different firmware. My previous one is Marlin V1.1 now the one i brought is P802M_8_V1.7. Problem: When i set x to home it rotby Rasyoni - Reprappers
I don't know about electricity that much. I tried my best: So I turn on the meter and set it to 200k and i get the measurement of 135.4 when I connect the measurement at the 2 ends of the thermistor, Hope am correct. Other than that yes i have the exact board.by Rasyoni - Reprappers
Thanks Dust! Yup now it stops the z axis but my happiness ends very shortly. Again another problem occurred I adjust the leveling and finally try to print a cube. So I use pronterface to print : All the sudden the heat bed light blinks and the lcd screen flickers like its short with power and all the display txts gone and it gives me an "Err:MINTEMP' in the pronterface. I tried to reset it by pby Rasyoni - Reprappers
I have attached the configuration file. It says "Zmax triggered"by Rasyoni - Reprappers
Thanks Dust; I have reverse the plug from the board and now it goes down but it wont stop even it touches the limit switch. I also send an M119 command and it works well i check for each switch and it works but the z axis when i home it it wants to go down crushing down the motherboard and ignores the limit switch. Any idea? Thanks a lot .by Rasyoni - Reprappers
Thanks all Now it seems rotating well. But my other problem is that how to print: I adjust the leveling measuring both z-axis the height equal I also adjust the bed equally But when i tell it to Auto home the axis move in different angle and move beyond the limit so it jumps the gears and belts. Is there a way or a simple guideline for manual prusa i3 reprap to configure it and adjust the leveliby Rasyoni - Reprappers
After assembling my new prusa reprap printer with your help guys i still couldnt figur out some problems፡ well when i select auto home or jog the z axis motors rotate individually to the opposite direction and my x axis it making loud noice and vibrating i check the belt no change. Finally my z axis motor is heated up fast is that normal while the others dont heat. Is it the firmware configuratiby Rasyoni - Reprappers
Thanks I noticed that i wire it wrongly on the board now it works fine.by Rasyoni - Reprappers
I tried to wire it on the opposite side but the thing is still switch off the display. I even replace the switch still the same. what else could be the problem. If its from the firmware is there any settings to check. I have a RepRap Prusa i3 Rework.by Rasyoni - Reprappers
I asembled a new rep rap prusa i3 i wired it perfectly. Managed to download the marlin firmware from the git hub "Marlin_Prusai3_reprap_pt" and successfully install it to the printer. Now the problem happens: when i go to 'auto home' in the control the z axis moves and presses the limit switch and it's off. Second the x axis seems struggling to rotate and makes a sound but i checked the belt itsby Rasyoni - Reprappers