hi i thought i would share my video about my incloser if you have questions just askby imjeffd1988 - Look what I made!
Tried it did not work my software on my laptop sends g90 then G1 then G91 I'm printing a part to do a way with the offsetby imjeffd1988 - Prusa i3 and variants
hello ever one i resiliently bought a printer on ebay that is just like the afinibot here is the link if you want to see it. ( ) there is some type of problem with the off set if i home a axis (x or y) it go's to the end stop then moves to the off set position but if i tell it to move lets say to x +50 it only moves to 50 from the end stop not 50 more it dose this on the x and y axis using its iby imjeffd1988 - Prusa i3 and variants
for some reason i can no longer print from my sd card i get this in the log it prints just fine over usb any ideas 23:21:06.141 : N76 M25*37 23:21:07.072 : N77 M105*23 23:21:08.172 : N78 M105*24 23:21:09.262 : N79 M105*25 23:21:09.615 : N80 M23 newest~1.gco*30 23:21:09.630 : N81 M24*44 23:21:09.635 : open failed, File: newest~1.gc. 23:21:10.351 : N82 M105*29 23:21:11.440 : N83 M105*28 23:21:11by imjeffd1988 - Firmware - Marlin
i have a printrbot simple 2014 the y axes has stopped working properly it jerks i have switched it with the x axes just to be sure but it still does not step right its an kysan1124103 its 42mm wide and 42mm tall and 32mm deep with a 5mm shaft but i don't know the voltage or the amps and when i search it i can't find anything this stepper motor looks like it would work it's 12v and .4 amps seem toby imjeffd1988 - Printing
the gcode is not in the center and the thing is the stl file that you made prints at the some size but if i scale it to 1.4 it prints on an angle this is some thing that i have noticed small prints seem to print correctly until i try to print a big part then it may or may not print correctly and big prints most the time print on an angle if you look at the first post the third photo "IMAG0367" iby imjeffd1988 - Printing
i have attached photo's of the settings that i use there some more in the next postby imjeffd1988 - Printing
ok sorry again for taking so long to get back with you i attach a photo of the gcode you shared it did not centered its self and i don't know how to center it. the stl file i printed that and it still printed outward on an angle here is a link to my google site at the top there is a file that is named "ring90mm.gcode" and some canning recipes as well the .gcode file is just to big to up-load i aby imjeffd1988 - Printing
in photo IMAG0378 the printer did not print on an angle the bolt looks a bit like it did but it just did not print the best and i picked it up and sat it back on the bed the y motor is between the to z rods and the problem started before i modified the bed and even though the resistors are inductive im not using pwm and even if i was i don't think there would be enough nose to mess any thing up tby imjeffd1988 - Printing
ok sorry i did not get back with you sooner i have been busy fixing my moms car and putting in a shower but anyway the thing is when i click on the slice button some times i get a message telling me something like the part is out of the print area even though it is not and even in the gcode editor it does not show it out side the print area so part of the program knows that it is going to be prinby imjeffd1988 - Printing
yes my printer is only 99mm x 99mm this is one of the reasons i wan't to make an reprap that and it keeps printing things to big by like .2mm to .45mm but anyway so i put a photo of my printer in a attachment it's a printerbot simple the strings that it uses are tight i also put a photo of it printing the ring with it printing a 10mm x 10mm x 10mm cube and a bolt but they all printed just fine noby imjeffd1988 - Printing
Quoteggherbaz Most likely the problem is in the STL file, run it through netfabb cloud and see if it fix it. ok so i made a circle in freecad and i sliced it in Slic3r and it printed out on an angle so sliced it in kissicer and the same thing happened so i unloaded to netfabb still same problem i attach the .stl file's i attached another photo it's of the settings i have the gcode flavor set toby imjeffd1988 - Printing
ok so i have a printrbot simple 2014 i know not RepRap but i am thinking about making it in to one but anyway so as in the photo's you can see one of the 5 squares started to lay down two infill's every layer and it would build up and i would take my knife and cut it to make it flat meany times so it could finish printing before that it printed on an angle in one of the photo's it shows this I uby imjeffd1988 - Printing