Show all posts by user
Page 1 of 5
Pages: 12345
Results 1 — 30 of 137
Guys,
I have an object to print, it's printed but why on the right hand side edge, it was not printed completely,
it's missing about 3mm to right ?
What's wrong here ?
Thanks
by
bianchi
-
Reprappers
Guys,
How can I pause printing when my filament is finished and I'm sleeping ?
Any ideas ?
Thanks
by
bianchi
-
Reprappers
Guys,
I tried to print something hanging from Z axis and some of them are not sticking each other properly, and I fixed it with epoxy glue,
Any solution for it ?
It's some kind a long tube and I print it horizontally because if I print vertically the bottom is very narrow to stick...
Any clues ?
Thanks
by
bianchi
-
Reprappers
Guys,
How can I put support for printing non flat object to Z axis ?
Thanks
by
bianchi
-
Reprappers
Guys,
Is it strong enough if I print a bike show with PLA ?
Thanks
by
bianchi
-
Reprappers
I'm using Scotch 3M 2093.....I can't find 2090 here.....
It's sticking like above example.....
I reduce it by putting cooking oil on it...
by
bianchi
-
Reprappers
Is it good if I use acrylic sheet for my heat bed ?
Like this one :
Acrylic sheet
by
bianchi
-
Reprappers
I used 2093 but it's sticking very well.....and I need to scrap the bottom part of the printed items...
Any ideas ?
by
bianchi
-
Australia, Melbourne RUG
After scrapping with sand paper...
by
bianchi
-
Reprappers
Probable I soak it with kerosene to clean the bottom part ? what do you reckon ?
by
bianchi
-
Reprappers
I have wipe it with alcohol before printing and using 30 degree heat on the bed but it's still sticking very well...
Please have a look:
Now I need to scrap it with sand paper to clean it.....
Any ideas to make it better.....? may be more alcohol ?
Thanks
by
bianchi
-
Reprappers
Scotch 2093EL blue masking tape...
by
bianchi
-
Reprappers
I've reduced to 30 but it's still sticking very well...any clues ?
by
bianchi
-
Reprappers
Guys,
I tried printing with Scotch 3M blue tape and PLA filament,
but by the time it's finished, I can not release the tapi from printed object,
I need to scrap it with sand paper...
Any ideas ?
Thanks
by
bianchi
-
Reprappers
Guys,
Why can't I reach 230 C on melzi board ?
I stuck at 205 C and difficult to go up again on my extruder ..
Thanks
by
bianchi
-
Reprappers
or :
Selleys 450g Linseed Oil Special Putty
by
bianchi
-
Reprappers
Can I use this one as a filler ?
Diggers 250g Fibreglass Resin
by
bianchi
-
Reprappers
Is a car body filler a paste or sprayable liquid?
by
bianchi
-
Reprappers
Anybody knows ?
I tried to print with it, why it's not sticking between layer, any solutions ? thanks
by
bianchi
-
Reprappers
Guys,
I tried to print with carbon PLA,
but strangely it's not sticking between layer.....what should I do to fix it ? thanks
by
bianchi
-
Reprappers
You can upload *.hex file directly to the chip....what's your board name ? please have a look on your PCB and what's the chip type...if it's marlin, it could be atmega1284P...
That's the one I use....
by
bianchi
-
Reprappers
Guys,
Is it possible for me using dual colors extruder with melzi board ?
Thanks
by
bianchi
-
Reprappers
Is your chip Atmega1284P ? what's your board name ?
If you need to flash it, you're going to need a programmer like USBASP for Atmega1284P, avrdude, some cables for connecting to its SPI port....
by
bianchi
-
Reprappers
Guys,
Can I paint PLA with acrylic clear paint ?
With this one :
White Knight 310g Crystal Clear Acrylic Clear Gloss
Thanks
by
bianchi
-
Reprappers
Do you mean FDM is "Fused deposition modelling (FDM)" ?
And may be for a simple test I make tube, and then give a stress with my weight plates 100kg and see what happen ?
what's the thickness of the tube normally ? there's a possibility that I make a frame / structure inside the tube, some kind a bone inside the tube for supporting the strength of it....
Thanks for your insight...
by
bianchi
-
Developers
It's in cm of course...
Do you reckon delta 30 x 18 would be good enough ?
I want to print a tube ( pipe ) for bicycle frame....is it possible with 20x20x20 printer ? then join all of them together ?
Thanks
by
bianchi
-
Developers
Guys does anyone of you build a large reprap? Any experiences I want to build 150x100x100
Thx
by
bianchi
-
Developers
Page 1 of 5
Pages: 12345