Search results
Create the page "Stripboard" on this wiki! See also the search results found.
- ...that it is also quite straightforward to make it on a couple of pieces of stripboard. That is how I prototyped it, and that is described below as well. == Making the electronics using stripboard ==20 KB (3,299 words) - 23:41, 5 February 2024
- = HOWTO: Building a stripboard Extruder Controller = * A piece of stripboard with 2.54mm (0.1") spaced continuous track.8 KB (1,325 words) - 20:07, 26 November 2011
- = HOWTO: Building A Stripboard Stepper Controller (for a Unipolar Motor) = * A piece of stripboard with 2.54mm (0.1") spaced continuous track. It should be a minimum of 23 h7 KB (1,090 words) - 06:34, 29 November 2014
- #REDIRECT [[Building A Stripboard Stepper Controller]]54 bytes (6 words) - 22:57, 20 February 2014
- # Move motors and electronics (still on stripboard) onto the new RepRap frame. ...tely functional RepRap, though it is not a true RepRap because it has some stripboard controllers and so on. The final step is to produce a new RepRap using the1 KB (240 words) - 14:32, 6 December 2011
- ...the ZD1901 opto interrupter prevalent in the Southern Hemisphere, a simple stripboard assembly is required. Details [[DarwinZD1901Opto|here]].7 KB (1,036 words) - 15:24, 23 July 2015
- If all this checks out and you have verified the stripboard soldering, then you can apply power to the board. If you have a multimeter This is based on the older, [[BuildingAStripboardCommsController|stripboard comms controller]] designed by Simon.16 KB (2,457 words) - 09:39, 26 November 2011
- If all this checks out and you have verified the stripboard soldering, then you can apply power to the board. If you have a multimeter This is based on the older, [[BuildingAStripboardCommsController|stripboard comms controller]] designed by Simon.13 KB (2,131 words) - 09:40, 26 November 2011
- If all this checks out and you have verified the stripboard soldering, then you can apply power to the board. If you have a multimeter * Which is based on the older, [[BuildingAStripboardCommsController|stripboard comms controller]] designed by Simon.15 KB (2,450 words) - 04:46, 25 July 2015
- ...cularly wants to do a board - is to solder it up onto a 6x11 hole piece of stripboard or veroboard. You will need to make 3 for the basic design, 6 if you wish t2 KB (334 words) - 09:47, 14 December 2014
- ...irst unless it is brand, spanking new with a mirror finish (see section on stripboard). Now you can start to solder stripboard. You did remember this is a practice run, right? Put the victim part in the11 KB (1,935 words) - 02:45, 29 December 2014
- * [[BuildingAStripboardExtruderController|A Stripboard Extruder Controller]] - This includes some details on heater element sizing20 KB (3,214 words) - 02:37, 4 March 2014
- ...t because there are so many wires to connect (they don't use a PCB or even stripboard). It works just fine though because I made mine as described, but it may b26 KB (4,452 words) - 14:31, 29 February 2012
- ...Mendel USB and power connector]] (no Eagle design - it's a simple piece of stripboard),10 KB (1,606 words) - 20:53, 19 February 2012
- I rapid prototyped a holder for a small piece of stripboard to go on the back of one of the geared motors that I used for the [[Thermop The larger part holds the stripboard for the electronics, and attaches using two 30 mm M3 cap screws to the hole11 KB (1,962 words) - 06:47, 13 May 2016
- ...the ZD1901 opto interrupter prevalent in the Southern Hemisphere, a simple stripboard assembly is required. Details [[DarwinZD1901Opto|here]].6 KB (986 words) - 09:44, 2 October 2012
- ...the ZD1901 opto interrupter prevalent in the Southern Hemisphere, a simple stripboard assembly is required. Details [[OptoEndstop_2_1#ZD1901_Opto_Switch|here]].16 KB (2,480 words) - 09:52, 14 December 2014
- * Which is based on the older, [[BuildingAStripboardCommsController|stripboard comms controller]] designed by Simon.22 KB (3,564 words) - 04:47, 25 July 2015
- ...rap.org/mediawiki/index.php?title=Special%3ASearch&search=stripboard&go=Go stripboard].9 KB (1,479 words) - 18:30, 26 November 2011
- * Top view of 2559 Stepper Motor on Stripboard: <br />900 bytes (130 words) - 06:13, 29 November 2014