Search results

Create the page "Warping" on this wiki! See also the search results found.

• Team Replicant
  ...is will enable to unit to act like a reflow oven and to minimize or reduce warping (as shown by many others).
  4 KB (695 words) - 18:38, 19 March 2014
• Glossary
  ...ded part from cooling (and shrinking) too quickly. Such shrinking leads to warping internal stresses in RP parts. The most common result is corners of parts l A heated build chamber is typically sealed and heated to prevent warping during the printing process.
  17 KB (2,735 words) - 22:34, 1 May 2024
• HDPE
  Larger and longer objects are likely to have more warping.
  3 KB (522 words) - 12:24, 18 March 2021
• BasicMendel
  ...e to warping of Plywood even high quality laser Plywood and MDF had slight warping (>0.5mm)
  8 KB (1,353 words) - 09:40, 18 September 2015
• Waxuum
  ...othing effect of the hot needle moving over the wax. There are also fewer warping, delamination, and anisotropy problems.
  8 KB (1,323 words) - 00:29, 1 September 2013
• BlueTape
  ...so unlike acrylic blue tape can be used in such a way that build platform warping is not an issue.
  2 KB (342 words) - 11:17, 3 May 2011
• Mendel heated bed
  ...surface. I can build entire trays of parts under those conditions with no warping.
  13 KB (2,361 words) - 21:26, 8 December 2013
• Feedstock
  ...de from corn starch. It prints very well and produces parts with almost no warping at all. It is harder and more brittle than ABS. It is colourless and clear.
  1 KB (245 words) - 15:09, 13 July 2012
• Huxley Seedling
  ...e to warping of Plywood even high quality laser Plywood and MDF had slight warping (>0.5mm) This thickness of Acrlic is needed to prevent warping of the Acrlic.
  9 KB (1,536 words) - 09:21, 18 September 2015
• MegaMendel
  ...but I have not yet tried to use the full build area. This is due to severe warping issues with my ABS plastic. I will try with PLA at some time to see how tha Some people say "heated bed" when the talk comes to warping, but I have decided not to go for that solution, the main reasons being:
  21 KB (3,936 words) - 10:31, 17 June 2016
• MetalicaRap
  ...tricky to print; the first layer must weld well to metal base to stop part warping, because cold platform contact hot metal residual stress tries to snap buil
  168 KB (26,821 words) - 07:28, 3 July 2023
• Elegant multispline motion controller
  * keep [[Heated Bed]] at the right temperature to prevent warping.
  29 KB (4,689 words) - 15:45, 4 January 2015
• Bed material
  *Electrical tape - sticks, but not well enough to stop warping. *Acrylic Sheet - works! ABS sticks to it quite nicely; I had some warping, but I only used 1.5 mm thick Acrylite FF P99 Acrylic Sheet from Cyro Indus
  13 KB (2,190 words) - 22:22, 16 April 2016
• Exquisite Automated Build Platform
  ...development project, however with any conveyor belt there are issues with warping, lift, and weight issues. If these were overcome perhaps development would ...a flat surface, and be designed sturdy enough to print for 100hrs without warping or adjustment
  11 KB (1,993 words) - 03:18, 14 February 2024
• Syringe Pump Metal Extruder
  ...not leak under the part. In general, the heated plate seems to help avoid warping, but the downside is that the bottom of the part starts to ooze outwards af
  8 KB (1,270 words) - 14:38, 22 January 2011
• OpenX
  ...structure is bellow the rails, putting it close to the hot end and risking warping from the heat plume.
  8 KB (1,446 words) - 08:48, 16 October 2013
• OpenY
  ...330 bearings onto the rails. currently, if it's way too loose, maybe from warping, you need to adjust a sketchup file and reprint something ...ith most of the RP parts below the rails. this would hopefully prevent any warping or distortion, but would require a greater redesign effort, and would proba
  7 KB (1,340 words) - 21:56, 14 December 2012
• RUG/Pennsylvania/State College/Printed Quadcopter
  ...parts are very large and flat, so extra caution should be taken to prevent warping during printing. The two sets of arms should be printed in two different co
  4 KB (535 words) - 11:14, 27 October 2014
• RAMPS 1.2
  ...inted in PLA. There is talk that it is currently unprintable in ABS due to warping.
  33 KB (5,279 words) - 13:40, 1 May 2013
• Mattroberts' Heated Bed
  ...ess (see left photo). In order to increase the grip (and therefore reduce warping) I sanded the stainless with some 150grit sandpaper, the result is a durabl
  3 KB (438 words) - 14:45, 12 November 2011

View (previous 20 | next 20) (20 | 50 | 100 | 250 | 500)