Search results

Jump to: navigation, search

Create the page "Arduino pololu" on this wiki! See also the search results found.

  • BeagleBone Black
    ...Pololu Shield]] (RAMPS) includes all the electronics necessary to turn a [[Arduino Mega]] into a dual-extruder RepRap controller). ...ard for the Arduino Mega, and borrows from the [[RAMPS-FD]] design for the Arduino Due.
    2 KB (304 words) - 00:19, 17 July 2019
  • RAMPS 1.4/kr
    |description = RepRap Arduino Mega Pololu Shield Arduino MEGA 기반 modular RepRap electronics.
    22 KB (3,149 words) - 20:31, 23 May 2020
  • Huxley/it
    * [http://ultimachine.com/catalog/electronics Ultimachine] (Arduino Mega/Pololu electronics) ** [http://www.pololu.com/catalog/product/1209 pololu NEMA14] (1400 g-cm holding torque!)
    18 KB (2,707 words) - 05:27, 11 April 2017
  • Prusa i3 Hephestos/fr
    ...l'aide d'un serre-câble. Guider les câbles assure que les radiateurs du Pololu ne soient pas recouverts. ...ns la plaque au coin supérieur gauche, il facilite le refroidissement des pololu en évitant d'avoir les câbles directement au-dessus des dissipateurs de c
    82 KB (12,253 words) - 18:24, 3 April 2016
  • Megatronics 3.0
    |description = Single board solution, Remix of Arduino mega and RAMPS |reprap = Pololu Electronics
    8 KB (1,321 words) - 18:07, 14 May 2024
  • RAMPS 1.4/zh tw
    ...y be installed if the 5A rail is powered by 12V. It can be omitted and the Arduino will be powered from USB. You will want D1 installed if you add components ...，方便焊接，但請注意別加熱時間太久，否則可能會損壞Arduino板上的零件。
    10 KB (1,118 words) - 11:28, 27 October 2014
  • Lawson
    ...UMBA]], [[Printrboard]], [[Generation 7 Electronics|GEN7]], [[Arduino Mega Pololu Shield|RAMPS]], and [[Rambo]].
    6 KB (953 words) - 02:38, 5 February 2017
  • Dragon 3D Printer
    Arduino Mega 2560 3 pololu stepper A4988 y 1 drv8825
    3 KB (549 words) - 07:55, 30 December 2014
  • Generation 7 Electronics/pt
    * 4x drivers para motor de passo Pololu, adaptável, até micro-passo 1/16. 09.02.2011: The master branch of FiveD on Arduino firmware is ported and seems to work but is not tested 100%. The config fil
    26 KB (4,024 words) - 03:21, 29 December 2014
  • Gen7 Board-AVR 1.5/pt
    * The Pololu Stepper Drivers come with their male headers, so there's no need to purchas ! Pololu Header
    27 KB (4,221 words) - 12:40, 25 March 2016
  • MKS GEN
    |description = Single board solution, Remix of Arduino mega2560 and RAMPS1.4 It features an onboard ATmega2560. Its five motor outputs are powered by Pololu pin compatible stepper drivers.
    7 KB (1,118 words) - 14:05, 28 December 2018
  • A4988 vs DRV8825 Chinese Stepper Driver Boards
    ...n than not, as inexpensive "Made in China" clones. Similarly, inexpensive "Pololu-style" stepper driver boards that plug directly onto RAMPS boards (usually ...]] driver boards are pin compatible with the [[Pololu_stepper_driver_board|Pololu A4988 Stepper Motor Driver Carrier]] but they have a different PCB layout w
    14 KB (2,301 words) - 20:28, 18 July 2016
  • SinapTec
    ...printer controller board of very low cost, its operation is based on an [[Arduino Nano]] or [[CHIP]] running a version of [[Teacup Firmware]]. The board layo 3d printer controller board based on Arduino Nano.
    12 KB (1,671 words) - 07:58, 10 October 2017
  • SAV MKI/pt
    * Suporte para 4 drivers compatíveis com Pololu, para motores passo a passo standard. * SDK: Arduino IDE com o complemento Teensy.
    18 KB (2,915 words) - 09:00, 9 December 2016
  • RAPS128
    ...per Driver with 1/128 Microstepping". The building size is the same as the Pololu drivers and the pin use is compatible, but not exactly the same as the Polo *Enable = HIGH (bei Pololu-Treibern LOW, in Firmware invertieren!)
    5 KB (640 words) - 11:40, 5 August 2016
  • RAPS128/de
    ...Driver with 1/128 Microstepping". Die Baugröße entspricht den beliebten Pololu-Treibern und die Pinbelegung ist kompatibel, aber nicht identisch. Die Trei *Enable = HIGH (bei Pololu-Treibern LOW, in Firmware invertieren!)
    5 KB (642 words) - 11:11, 21 February 2015
  • Blu Bot 1.0
    ...er Controller RAMPS 1.4 Arduino Mega Pololu Shield for Reprap Prusa Mendel Arduino Mega2560 '''Arduino board'''
    11 KB (1,692 words) - 02:25, 1 May 2015
  • BAM&DICE
    |description = Arduino Mega shield for multiple applications = BAM&DICE for Arduino Mega =
    12 KB (1,762 words) - 23:50, 10 October 2017
  • SmartOne 150
    ...UMBA]], [[Printrboard]], [[Generation 7 Electronics|GEN7]], [[Arduino Mega Pololu Shield|RAMPS]], and [[Rambo]].
    2 KB (275 words) - 06:39, 16 May 2015
  • CARP Box
    Mounting holes are prepared for Sanguinololu 1.3a and Arduino Mega 2560 with RAMPS 1.4. There may be slight differences between original In above mentioned electronics, Pololu drivers or its cones are used. There are two most common drivers.
    7 KB (1,127 words) - 10:34, 17 June 2016

View (previous 20 | next 20) (20 | 50 | 100 | 250 | 500)

Retrieved from "https://reprap.org/wiki/Special:Search"