Search results

Jump to: navigation, search
  • * Which is based on the older, [[BuildingAStripboardCommsController|stripboard comms controller]] designed by Simon.
    22 KB (3,564 words) - 04:47, 25 July 2015
  • ...rap.org/mediawiki/index.php?title=Special%3ASearch&search=stripboard&go=Go stripboard].
    9 KB (1,479 words) - 18:30, 26 November 2011
  • * Top view of 2559 Stepper Motor on Stripboard: <br />
    900 bytes (130 words) - 06:13, 29 November 2014
  • File:StepperDriverWithUDN2559-2559 Stepper Stripboard top.png
    Top view of 2559 Stepper Motor on Stripboard
    (516 × 606 (153 KB)) - 07:55, 17 March 2010
  • ...Rap controller boards. It is very simple to solder up on an old offcut of stripboard, or you can get a proper [http://parts.rrrf.org/product_info.php?products_i
    1 KB (230 words) - 20:05, 26 November 2011
  • ...also cheap, only $5.00 USD. It is also apparently possible to build it on stripboard - if you do so, please share the instructions with us!
    24 KB (4,088 words) - 05:55, 29 November 2014
  • = HOWTO: Build A Stripboard Bipolar Slave Stepper Controller = * [[StripboardBipolarStepperController|HOWTO Build a Stripboard Bipolar Stepper Controller]]
    1 KB (158 words) - 05:08, 25 July 2015
  • File:StripboardBipolarSlaveStepperController-StepperSlaveStripboardUnder 754410.gif
    Underside of stripboard
    (375 × 430 (23 KB)) - 08:01, 17 March 2010
  • = HOWTO: Build A Stripboard Bipolar Stepper Controller = ...order repeatedly. The pinouts are 1 to 4 as seen from the top-down on the stripboard. Where you see 1->2 this means the voltage measured from pin 1 (negative p
    6 KB (906 words) - 05:09, 25 July 2015
  • #REDIRECT [[Build A Stripboard Bipolar Stepper Controller]]
    59 bytes (7 words) - 05:09, 25 July 2015
  • File:StripboardBipolarStepperController-StepperStripboardUnder 754410.gif
    Underside of stripboard
    (342 × 523 (27 KB)) - 08:01, 17 March 2010
  • ...ication on plain perforated board. The design outlined here uses the same stripboard methods as suggested for other modules and is simpler to build. This image shows the rear of the stripboard so you can see the points that were separated.
    7 KB (1,092 words) - 05:11, 25 July 2015
  • File:StripboardJDM-JDMStripboardUnder.gif
    Underside of stripboard
    (650 × 385 (48 KB)) - 08:01, 17 March 2010
  • ...made the circuit for driving the extrusion head conventionally on 2.54 mm stripboard. ...tomatically creating PCBs if you want to etch one, rather than building on stripboard. If you do that, put two 3 mm mounting holes on one edge of the PCB 32 mm
    52 KB (8,773 words) - 09:49, 5 January 2015
  • ...I did not have a [[PWM_Driver_1_1|RepRap PWM PCB]] to hand, and it is that stripboard circuit that is shown.
    2 KB (344 words) - 14:19, 29 November 2011
  • ...Rap controller boards. It is very simple to solder up on an old offcut of stripboard. ...u want to do this, put a 7-pin connector in for P11, make up your circuit (stripboard is probably easiest), and put a 7-way socket on the board that will plug in
    19 KB (3,040 words) - 04:53, 25 July 2015
  • ...u want to do this, put a 7-pin connector in for P11, make up your circuit (stripboard is probably easiest), and put a 7-way socket on the board that will plug in
    31 KB (5,053 words) - 04:54, 25 July 2015
  • ...rt as a drilling jig to drill two 4mm holes near to the bottom edge of the stripboard. Solder the two 4-pin headers near the top and towards either end. Split ...shers down the holes in the driven holder, using the top two to retain the stripboard.
    15 KB (2,556 words) - 00:59, 5 February 2024
  • ...le electronics that can be printed by RepRap itself. Can also be built on stripboard. Fully tested, and supported by the standard RepRap software. ...ew%20Front%20Page/Documentation/Tools/Stripboard%20designer.htm]. See the "Stripboard Designer" section of [[Useful Software Packages]].
    18 KB (2,604 words) - 08:58, 6 May 2020
  • I wired up the control circuit on stripboard, with the power MOSFET on a meaty heatsink. Make sure that all the high-cu
    13 KB (2,361 words) - 21:26, 8 December 2013

View (previous 20 | next 20) (20 | 50 | 100 | 250 | 500)