Search results

Jump to: navigation, search

Create the page "Arduino pololu" on this wiki! See also the search results found.

  • Ultimaker
    * Ships with official Arduino Mega 2560. Soon to ship with Open Source Pololu stepper driver replacement (open source upon first shipping). ...er-cura Cura] to upload firmware to the controller board, then you can use Arduino IDE or PlatformIO in order to compile and upload the firmware you get from
    12 KB (1,816 words) - 21:17, 14 October 2023
  • Helium Frog Delta Robot
    ...c system is likely to be Arduino Mega based. Stepper motor drivers will be pololu based. The motors will be Nema 17 Model(SY42STH47-1684B)
    3 KB (429 words) - 11:15, 6 February 2015
  • RedBot
    ...ulators from a [[RUG/UK|uk]] based company. **UPDATE** just arrived, there pololu's so should do a very good job!
    5 KB (907 words) - 00:37, 12 March 2021
  • Build a RepRap
    ...ize various electronics configurations, such as RAMPS (RepRap Arduino Mega Pololu Shield), Smoothieboard, or custom-designed boards. Understanding the electr
    4 KB (561 words) - 11:58, 4 May 2024
  • Troubleshooting
    [[Arduino Mega Pololu Shield#Trouble Shooting | RAMPS Troubleshooting]] - RAMPs troubleshooting
    9 KB (1,431 words) - 17:55, 26 December 2015
  • Repic
    ...mplete set of Repic-based electronics costs around $80, including the four Pololu stepper drivers. I am currently researching ways to safely replace the Polo For the main controller of my motherboard I have replaced the Arduino-based architecture with one based on the Microchip PIC series. My current P
    16 KB (2,557 words) - 23:14, 5 November 2022
  • Ultimaker's v1.1 PCB
    |description = A 5 axis RepRap ArduinoMega Pololu Shield | Arduino MEGA [[Ultimaker]] Shield v1.1.brd (old)
    22 KB (3,651 words) - 09:21, 17 December 2011
  • Ultimaker's v1.3 PCB
    |description = A 5 axis RepRap ArduinoMega Pololu Shield ...ectronics]] as it is directly "[[RAMPS]]" based: RepRap [[Arduino Mega]] [[Pololu]] Stepper. It will be available from the [https://shop.ultimaker.com/ Ultim
    2 KB (233 words) - 07:53, 17 December 2011
  • RUG/Czech Republic
    * [http://www.hwkitchen.com/ HW Kitchen] - Arduino a shieldy (Šenov) ...truments.com SnailInstruments] - RAMPS 1.4 a ovladače krokových motorů (Pololu 1182) (Beroun)
    6 KB (1,049 words) - 09:07, 8 July 2014
  • RUG/Australia/Suppliers
    ...w.bilby3D.com.au Bilby3D] - RAMPS 1.4, Gen6, Pololu A4988 stepper drivers, Arduino Megas. ...://www.robotronics.com.au Robotronics] - RAMPS 1.4, A4988 stepper drivers, Arduino Megas, Thermistors, Cartridge Heaters, Fans, Wiring, Micro Switches.
    28 KB (4,489 words) - 02:35, 26 May 2020
  • Ultimaker's v1.5.3 PCB
    |description = A 5 axis RepRap ArduinoMega Pololu Shield | Arduino MEGA [[Ultimaker]] Shield v1.5.3.brd (old)
    12 KB (1,920 words) - 09:25, 17 December 2011
  • RAMPS 1.2 old
    |description = A RepRap etch resist printable circuit board that fits on the Arduino MEGA and holds interchangeable stepper driver carriers and the rest of RepR Arduino MEGA based modular RepRap electronics.
    10 KB (1,696 words) - 17:01, 5 April 2014
  • Sanguinololu
    |reprap=Pololu Electronics#Sanguinololu ...gh a 644, 1284 or 1284P is easily dropped in. Its four axes are powered by Pololu pin compatible stepper drivers. The board is designed to be flexible in its
    43 KB (6,616 words) - 20:02, 10 February 2024
  • StepStick
    :''Please note: StepStick has 0.2 ohm sense resistors instead of [[Pololu stepper driver board]]s 0.05 ohm. This limits the current to 1A. See [[Not [[Category:Pololu electronics]]
    16 KB (2,587 words) - 07:51, 2 June 2020
  • Sanguinololu 0.6
    You will also need Pololu or Pololu compatible stepper drivers such as [[StepStick]] ...the leads first so that the capacitor lays down and doesn't interfere with pololu installation C1, C2, C3, C4
    11 KB (1,589 words) - 11:23, 30 November 2014
  • Prusa Mendel Assembly
    ...ou may find the [http://arduino.cc/ Arduino] [http://www.ladyada.net/learn/arduino/index.html Tutorials on Adafruit] quite useful. ...mparison to parallel wiring. That is (for that particular motor and using Pololu/[[StepStick]] phase designations):''
    49 KB (8,907 words) - 04:18, 14 February 2024
  • Teensylu
    ;* Up to 4 [[Pololu stepper driver board]]s (or Pololu compatible) on-board (X,Y,Z,Extruder) (without voltage regulator) *(Other firmwares are currently untested but any firmware for an arduino mega should work with proper pin setup.)
    13 KB (1,808 words) - 06:29, 5 April 2015
  • RAMPS 1.3
    |description = RepRap Arduino Mega Pololu Shield Arduino MEGA based modular RepRap electronics.
    23 KB (3,768 words) - 18:06, 7 March 2019
  • Azteeg X3
    |reprap = Arduino, RAMPS We've combined the RAMPS and the Arduino Mega into one sleek package, added lots of cool stuff, beefed up power hand
    16 KB (2,667 words) - 11:27, 9 July 2015
  • Gen7 Board 1.2
    * The [[Pololu]] Stepper Drivers want two single rows of 8 pin female connectors soldered * The [[Pololu]] Stepper Drivers come with their male headers, so there's no need to purch
    20 KB (3,229 words) - 14:50, 14 November 2015

View (previous 20 | next 20) (20 | 50 | 100 | 250 | 500)

Retrieved from "https://reprap.org/wiki/Special:Search"