Subject		Views	Posts	Last Post
	Alignment issues by simono71	702	5	12/16/2012 09:33PM Last Post by simono71
	Negative bed temperature? by kev	1,330	6	12/16/2012 04:40PM Last Post by kev
	ramps 1.4 board led blinking by zipfactor	10,510	8	12/16/2012 02:17PM Last Post by zipfactor
	New lcd interface by akhlut	597	3	12/16/2012 01:50PM Last Post by jcabrer
	Abs bridges by Enlightx	2,807	9	12/16/2012 01:26PM Last Post by Enlightx
	What causes this by tmorris9	1,055	15	12/16/2012 02:09AM Last Post by NoobMan
	You can print pulleys from Mcmaster/SDPSI without paying for software - and results by Simba	1,470	3	12/15/2012 05:51PM Last Post by 691175002
	How cold can the room temperature get before it is a bad idea to print with PLA? by PeteD	3,501	14	12/15/2012 04:25PM Last Post by NoobMan
	Help with Mondo by ludara	716	3	12/14/2012 11:13PM Last Post by ludara
	Filament without a spool by marcosscriven	2,758	12	12/14/2012 06:54PM Last Post by nophead
	It’s time to step forward – BCN3D – The new 3D Printer by RepRapBCN	2,618	3	12/14/2012 03:45PM Last Post by RepRapBCN
	J Head Extrusion problem by 3eality	1,352	10	12/14/2012 10:30AM Last Post by scwerta
	20 seconds survey about 3D printing by JFH	600	1	12/14/2012 09:57AM Last Post by JFH
	Solved: Relation between nozzle size, length and extrusion force (pressure) by tprime	856	4	12/14/2012 04:02AM Last Post by konwiddak
	Complete beginner question. Printing over hangs etc by SNGLinks	802	4	12/14/2012 12:32AM Last Post by Simba
	J-head melting when trying to print with ABS by Benjamin Engel	2,626	16	12/12/2012 10:29PM Last Post by brnrd
	beware of the clones by thejollygrimreaper	744	2	12/12/2012 09:53PM Last Post by akhlut
	Carbon from the atmosphere as a printing material by jjalexand	620	2	12/12/2012 08:56AM Last Post by VDX
	Advice on a new ramps board, heat in arduino usb port, and highly geared stepper by Simba	654	1	12/11/2012 07:14PM Last Post by Simba
	ABS/PLA safety during Pregnancy by parkster	3,364	16	12/11/2012 03:44PM Last Post by PeteD
	First ever "pop up" 3d printer store and review by Simba	760	5	12/11/2012 11:44AM Last Post by PeteD
	[PROBLEM] Homes through endstops by mv2woods	689	2	12/11/2012 10:26AM Last Post by CdnReprap
	Best PLA color for noobs? by lions3	6,991	11	12/10/2012 10:50PM Last Post by NewPerfection
	no warp design by rogerw	1,304	23	12/10/2012 10:32PM Last Post by jamesdanielv
	Multiple hotends/toolheads thoughts by Polygonhell	646	2	12/10/2012 09:01PM Last Post by wolfkeeper
	[solved] Filament gets stuck very often by arthurmani	1,023	9	12/10/2012 08:34PM Last Post by jamesdanielv
	Which nozzle will do better? by theodleif	887	10	12/10/2012 05:51PM Last Post by Idolcrasher
	Extruder Choking... (PIC Inside) Need Your Thoughts by Idolcrasher	1,398	15	12/10/2012 05:44PM Last Post by Idolcrasher
	How do. by johnwiseman	742	5	12/10/2012 05:30PM Last Post by johnwiseman
	clueless gift giver in Xmas rush by Deckard	582	3	12/10/2012 04:03PM Last Post by Simba