Subject		Views	Posts	Last Post
	Geared Extruder Nozzle...Pictures Posted...Now on Ebay   (Pages: 1 2) by reifsnyderb	2,083	32	10/21/2010 10:04AM Last Post by reifsnyderb
	2nd layer not printing on first by bbriggstkd	1,081	15	10/20/2010 09:43PM Last Post by bbriggstkd
	on the subject of bearings and rails by Anthong Redbeard	1,003	4	10/18/2010 08:38PM Last Post by Anthong Redbeard
	Un nouveau ! by lucf	859	6	10/18/2010 06:53PM Last Post by ZaphodBeeblebrox
	Seen this yet? MakerBot Automated Build Platform by Jayson	1,180	10	10/18/2010 02:26PM Last Post by D1plo1d
	Teach Me Build a RepRap Mendel by rimsky	897	1	10/18/2010 01:34PM Last Post by rimsky
	reprap software help by hazuki	1,077	7	10/16/2010 07:51PM Last Post by hazuki
	Wanting to do Mendal for my Dissertation but can't think of any new ideas, any suggestions? by RepRap_GCALman	1,201	18	10/15/2010 03:19PM Last Post by rocket_scientist
	Electrical noise in temperature measurement? by Koko76	2,738	9	10/15/2010 02:41PM Last Post by rocket_scientist
	Ready for the software.... advice please by AgeingHippy	1,299	6	10/14/2010 09:12PM Last Post by Anthong Redbeard
	Huxley mini-mendel and McMaster-Carr parts list? by pica	1,646	4	10/14/2010 08:14PM Last Post by pica
	Reprap chat room by Jayson	1,303	3	10/14/2010 06:59PM Last Post by Jayson
	Reachout aka "Evangelism" by peer	1,359	6	10/13/2010 11:03AM Last Post by pica
	[USA] Average ebay prices for Reprap ABS parts kits $224.33 by pica	1,463	17	10/13/2010 11:00AM Last Post by pica
	3d systems buy bits from bytes by johnrpm	1,880	20	10/13/2010 08:33AM Last Post by spacexula
	Sizing of models to Mendel by Phobia1	1,393	5	10/12/2010 01:57PM Last Post by Phobia1
	Reprap software vs replicatorg by hazuki	1,301	2	10/12/2010 02:48AM Last Post by rhmorrison
	Where can I get recommendations for designing parts (thickness, etc) by cluso99	882	12	10/11/2010 11:23PM Last Post by mlagana
	getting resolution into the microns by mlagana	1,159	10	10/11/2010 05:46PM Last Post by pica
	Stepper driven extruder by zeneslev	812	2	10/11/2010 12:28AM Last Post by mlagana
	Source PLA/ABS filament...in China by sam0737	2,424	5	10/10/2010 11:56AM Last Post by Lawrence
	Clothes iron as a heated bed? by Greg Frost	4,597	4	10/09/2010 06:04PM Last Post by richrap
	Isolation Milling Of PCB's by Cynic	2,160	6	10/09/2010 05:14AM Last Post by Traumflug
	Vapour Smoothing System (HP) by richrap	1,560	10	10/08/2010 06:52PM Last Post by murrayd
	Mantis 9.1 by spacexula	2,503	16	10/07/2010 03:01PM Last Post by rocket_scientist
	knurling knowledge kneeded by rocket_scientist	1,691	17	10/07/2010 02:05PM Last Post by Bruce
	PEEK for Geared Extruder on ebay. by KeithSloan	923	1	10/07/2010 12:15PM Last Post by KeithSloan
	Bushes - Question for Josef Prusa by cluso99	814	2	10/06/2010 10:42PM Last Post by tesla893
	For developing new forms of printers. by ZaphodBeeblebrox	922	4	10/06/2010 04:43PM Last Post by Koko76
	Makerbot 3G and firmware question by AgeingHippy	858	4	10/06/2010 08:43AM Last Post by VDX