Subject		Views	Posts	Last Post
	The step motor starts the movement but does not complete by dsacheti	427	3	05/07/2017 06:55PM Last Post by scottybfg
	Different results with ABS when printing parts sliced with Cura and Slic3r by David J	629	4	05/05/2017 01:47AM Last Post by o_lampe
	Bed not levelled after Auto Level by RVE	9,359	19	05/03/2017 10:38PM Last Post by johnmayo
	My printer just started printing circles as ovals and squares as rectangles... by dantyas	827	8	05/03/2017 01:25PM Last Post by dantyas
	Extruder problem by omarbentaleb	494	1	05/03/2017 07:19AM Last Post by omarbentaleb
	MKS Base Filament Runout Sensor by GreatBazunka	1,198	1	05/02/2017 08:20PM Last Post by GreatBazunka
	PLA Lifting in Back by GrahamCracker	756	6	05/02/2017 01:39AM Last Post by scottybfg
	Under-Extrusion Type Issue by Undisclosed	719	2	04/27/2017 07:42PM Last Post by Soadyheid
	Object Dimensions are skewed after changing nozzle and controller by fullHundo	483	5	04/27/2017 06:29PM Last Post by scottybfg
	Slic3r not making proper vase mode by Alandac	603	3	04/27/2017 04:16AM Last Post by Alandac
	Please help! Printer speed is so slow by naimvincent	621	12	04/25/2017 02:25PM Last Post by naimvincent
	Printing speed / Moves problems by lezabour	544	4	04/25/2017 11:18AM Last Post by lezabour
	"mirrored" prints by clogs51	781	9	04/23/2017 07:23AM Last Post by o_lampe
	Prusa i3 bad printing on specific objects by ppanos80	670	5	04/21/2017 12:16AM Last Post by n9jcv
	Flex3Drive eSteps issue by CliffAgius	1,060	3	04/20/2017 07:12PM Last Post by Mutley3D
	[old PLA] bubbles in print by chngyian	1,071	2	04/20/2017 08:56AM Last Post by Evan
	dual extruder shifted parts by Schild0r	666	6	04/18/2017 08:14AM Last Post by Schild0r
	lcd screen missing line by clogs51	558	2	04/15/2017 09:55AM Last Post by obewan
	Discover over under extrusion by batata004	476	2	04/15/2017 04:38AM Last Post by Supermec
	Prusa I3 awful printing quality by yupiter00	569	3	04/14/2017 02:28PM Last Post by yupiter00
	Extrusion issues above specific Z by rich1051414	535	1	04/14/2017 04:50AM Last Post by rich1051414
	Printer not making holes with good dimensions by batata004	561	9	04/13/2017 01:41PM Last Post by Floyd
	Auto Bed Leveling Not Moving Z Axis While Printing by drewskeeh	868	2	04/12/2017 06:14PM Last Post by drewskeeh
	Dead RAMPS? "Extruder Switched Error" by akamrkent	557	6	04/12/2017 02:10AM Last Post by o_lampe
	What printing problem could be this? by DOYT	1,571	5	04/10/2017 11:52AM Last Post by DOYT
	Is this over extrusion? by Desertboy	731	6	04/10/2017 11:14AM Last Post by Desertboy
	Deformation test by chriske	438	2	04/09/2017 05:11PM Last Post by lockezio
	Round perimeter by chriske	591	2	04/07/2017 08:35AM Last Post by the_digital_dentist
	Does layer content change layer width? by drmaestro	543	5	04/07/2017 06:55AM Last Post by drmaestro
	Printing issues at 0.1mm by DOYT	608	4	04/07/2017 03:47AM Last Post by o_lampe