Welcome! Log In Create A New Profile

Ormerod

RepRapPro's Ormerod http://reprap.org/wiki/Ormerod

Page 74 of 83 Pages:

72 737475 76

Forum List New Topic RSS

	Views	Posts	Last Post
M30 command not working? by djb	826	5	01/30/2014 06:45PM Last Post by iamburny
WebServer Down by Pendragon	517	1	01/30/2014 06:36PM Last Post by Pendragon
Any bright ideas? by GregL	778	12	01/30/2014 04:03PM Last Post by PaulHam
Setting Z axis height by Rotorflush	881	6	01/30/2014 01:46PM Last Post by dc42
SD card cannot be read by Due by Ingeneo70	657	9	01/30/2014 12:16PM Last Post by dc42
Poor quality bearings- Solution anyone? by gregstah	1,221	3	01/30/2014 08:22AM Last Post by victors
Idle musings on mass production by Radian	2,343	14	01/29/2014 08:10PM Last Post by dmould
Updated troubleshooting instructions by droftarts	520	4	01/29/2014 05:52PM Last Post by Ormerod276
Head Temperature Oscillating by johneato	522	5	01/29/2014 03:34PM Last Post by johneato
Slic3r and Temperatures by johneato	811	5	01/29/2014 01:44PM Last Post by johneato
Slic3 question by Ormerod276	892	6	01/29/2014 09:06AM Last Post by dmould
adding axis stop/homing switches to Z and X by rayhicks	1,518	19	01/29/2014 08:36AM Last Post by dmould
large prints? by gman	513	5	01/29/2014 06:54AM Last Post by arnaud31
Out of Curiosity (Rover) by Radian	706	7	01/29/2014 04:43AM Last Post by Radian
Ormerod / Duet error message by d2d	837	5	01/29/2014 04:21AM Last Post by d2d
Tuning printing parameters by aesuli	935	6	01/28/2014 10:26AM Last Post by dc42
No more than 24 file listed from SD with M20 command by aesuli	726	14	01/28/2014 08:23AM Last Post by dmould
Reason for unsupported linear bearing by tracyb	606	5	01/28/2014 04:21AM Last Post by tracyb
Z lead screw nut thread stripped (Pages: 1 2) by arnaud31	4,415	46	01/27/2014 05:52PM Last Post by KimBrown
SD Card reader by XB70	536	2	01/27/2014 05:47PM Last Post by KimBrown
support structures - need help by #442	877	6	01/27/2014 03:01PM Last Post by dmould
A general question about CAD by KimBrown	1,412	13	01/27/2014 12:28PM Last Post by dmould
The Progression of Kit278 (Pages: 1 2 3 4) by victors	4,531	118	01/27/2014 10:13AM Last Post by rayhicks
Slic3r failure to save configuration in Ubuntu 12.04 by DennisCowdery	583	2	01/27/2014 10:02AM Last Post by droftarts
Commissioning problems by MEL-101	573	4	01/27/2014 09:45AM Last Post by droftarts
Updated commissioning instructions by droftarts	967	18	01/27/2014 08:59AM Last Post by badman.teddy.edward
Maximum print speed ? by tru168	492	5	01/27/2014 08:30AM Last Post by tru168
Laser cutter ideas by Squags	530	1	01/27/2014 05:47AM Last Post by Squags
Is there any good reason not to print PLA direct on glass? by dc42	1,504	9	01/27/2014 04:09AM Last Post by onno
First Layer by johneato	1,594	15	01/27/2014 03:33AM Last Post by victors

Page 74 of 83 Pages:

72 737475 76

Ormerod

Z lead screw nut thread stripped (Pages: 1 2)

The Progression of Kit278 (Pages: 1 2 3 4)