Welcome! Log In Create A New Profile

Elettronica e meccanica

Discussioni sulle parti elettriche ed elettroniche, motori, endstop, etc. Parliamo di struttura della stampante, pulegge, madreviti, boccole, viti trapezoidali, etc.

Page 53 of 54 Pages:

50 51 525354

Forum List New Topic RSS

	Views	Posts	Last Post
utilizzo stepper driver esterni per ramps: aiuto! by zaius	1,331	15	03/19/2014 09:49AM Last Post by enricodare
Ricerca info prusa I3 asse Y e consigli endstops by Federico22	1,377	19	03/18/2014 12:32PM Last Post by Federico22
Hobbed bolt fai da te by mic	549	4	03/18/2014 02:42AM Last Post by Nicola P
Connettori: Come si chiamano? by enricodare	985	4	03/17/2014 04:58PM Last Post by enricodare
aiuto alimentatore pc by ufra	1,895	18	03/16/2014 01:52PM Last Post by ufra
Domanda "bizzarra" sulle barre rettificate..... (Pages: 1 2 3) by Alex9000	3,983	61	03/15/2014 04:32PM Last Post by sipperton
Problema Temperatura 0° - ramps 1.4 - marlin 1.0 by djscolla	1,366	18	03/15/2014 08:31AM Last Post by lion_heart78
Avanzamento assiale Z [Risolto] by Tatasala	550	5	03/14/2014 01:38PM Last Post by Tatasala
Elettronica Gen7...info su wiki errate.. [Risolto] by ninjamcrew	491	13	03/14/2014 07:29AM Last Post by Gordie
Info Cuscinetti 608-2rsh [Risolto] by Alex9000	641	9	03/13/2014 05:41PM Last Post by Alex9000
Driver DRV8825 - Scarso funzionamento o sbaglio io? by albybot	1,514	11	03/13/2014 10:43AM Last Post by albybot
arduino puo funzionare a 24 volt? (risolto) by massimo	672	7	03/13/2014 05:16AM Last Post by massimo
MEGATRONICS V3 REPARP WORLD [risolto] by jonathan	481	2	03/13/2014 04:51AM Last Post by Gordie
Problema di calibrazione asse z? [Risolto] (Pages: 1 2) by il boso	4,469	43	03/12/2014 06:57PM Last Post by ninjamcrew
Livellamento del piano by Ilpelo92	627	6	03/12/2014 05:04PM Last Post by bertnick
malfunzionamento movimento assi by AQUISHARK	513	2	03/12/2014 07:03AM Last Post by Ivan Bortolin
Ventola si o no ? Perchè? Quando? by momix	1,769	7	03/11/2014 12:11PM Last Post by lion_heart78
megatronics non funziona con sketch di test (RISOLTO) by nik89	591	14	03/11/2014 07:21AM Last Post by nik89
Poco abs estruso by acktung77	613	11	03/10/2014 05:03PM Last Post by bonjolo
Arduino mega 2560.... R3 o non R3 ??? [Risolto] by Alex9000	593	2	03/09/2014 04:10PM Last Post by Alex9000
Problemi motore nema 17 e drive DVR8825 by Leo75	1,337	9	03/08/2014 04:16PM Last Post by bonjolo
Alimentatore bruciato?! [Risolto] by il boso	816	5	03/08/2014 10:58AM Last Post by il boso
area di stampa dubbio by DeAndreon	1,098	7	03/07/2014 09:16PM Last Post by enricodare
megatronics v3 [Risolto] by nik89	1,141	8	03/07/2014 09:01PM Last Post by bonjolo
End_stop schema collegamento giusto? by RikyRap	996	4	03/07/2014 06:51AM Last Post by Gordie
Prima prova con Motore nema 17 + ramps 1.4 by Condor	827	4	03/06/2014 04:06PM Last Post by bonjolo
Problema serio asse z by momix	722	16	03/05/2014 01:22PM Last Post by momix
Coppia , micropassi e approssimazione. by Bigo	1,529	4	03/05/2014 01:10PM Last Post by Nicola P
Problema end stop z by BonuS	832	14	03/05/2014 02:48AM Last Post by BonuS
Sibillio motori by RikyRap	492	2	03/04/2014 06:45PM Last Post by Gordie

Page 53 of 54 Pages:

50 51 525354

Elettronica e meccanica

Domanda "bizzarra" sulle barre rettificate..... (Pages: 1 2 3)

Problema di calibrazione asse z? [Risolto] (Pages: 1 2)