Welcome! Log In Create A New Profile

CoreXY Machines

http://reprap.org/wiki/CoreXY

Page 9 of 20 Pages:

Forum List New Topic RSS

Subject		Views	Posts	Last Post
	Hbot Motor inverted by mogey336	884	4	03/19/2018 07:18PM Last Post by the_digital_dentist
	New printer design with new 'twist' for XY on Z (Pages: 1 2) by klcjr89	2,808	58	03/16/2018 05:51PM Last Post by klcjr89
	Z axis gantry vs Z axis printbed by Vigilant	2,387	13	03/13/2018 08:01AM Last Post by the_digital_dentist
	Cable management to the X-Y carriage - how did you do it? by David J	7,984	15	03/09/2018 10:34AM Last Post by the_digital_dentist
	To twist or not to twist by appjaws1	5,223	28	03/09/2018 04:24AM Last Post by MKSA
	New Printer Design by Speaker-2-Animals	1,613	20	03/08/2018 11:40AM Last Post by Speaker-2-Animals
	MiniM's Core XY project (Pages: 1 2) by minim	9,398	35	03/08/2018 08:29AM Last Post by psxsnake
	My CoreXYU Printer project (Pages: 1 2 3 4) by lars.arvidson	12,725	111	03/04/2018 07:20PM Last Post by prot0typ1cal
	Large CoreXY Z Lift by Mathew96	1,325	13	02/16/2018 06:08AM Last Post by Mathew96
	Homing in Corexy is not at 0,0,0 by methesoul	949	2	02/14/2018 01:26PM Last Post by methesoul
	Trying to tune my CORE XY by brand0drag0	1,858	6	02/07/2018 02:32AM Last Post by o_lampe
	Print banding problem by appjaws1	939	4	02/06/2018 04:15AM Last Post by MKSA
	Tall print issue in X direction by aceranic	742	14	02/05/2018 09:30AM Last Post by aceranic
	One corner issue by aceranic	651	3	01/27/2018 12:58PM Last Post by aceranic
	Help with strange blobs/calibration by coredump	645	4	01/26/2018 03:20AM Last Post by o_lampe
	How can i configure Hbot on marlin firmware? by mogey336	3,031	4	01/26/2018 03:14AM Last Post by o_lampe
	20x20 aluminium tubing frame by DLF	1,587	9	01/11/2018 01:46PM Last Post by DLF
	Cyclonit's CoreXY by Cyclonit	1,999	13	12/30/2017 01:32PM Last Post by Qdeathstar
	Witor's coreXY by witor	2,105	11	12/30/2017 12:47AM Last Post by prot0typ1cal
	My printer is now printing.. by flydeprutten	1,442	13	12/13/2017 03:57AM Last Post by flydeprutten
	Newbie looking for some setup guidance... (Pages: 1 2) by ampapa	4,147	48	12/10/2017 12:47PM Last Post by dc42
	Z motor noise from binding... how do you align? by ampapa	1,544	9	12/05/2017 07:45AM Last Post by the_digital_dentist
	Problemas con finales de carrera by alenarmi	825	4	12/02/2017 10:00AM Last Post by alenarmi
	problemas con el extrusor by alenarmi	640	1	12/02/2017 09:56AM Last Post by alenarmi
	E3D Titan on a D-Bot carrier by o_lampe	938	2	11/30/2017 05:02AM Last Post by MKSA
	The location of the Z endstop by flydeprutten	1,856	3	11/27/2017 07:47AM Last Post by flydeprutten
	24V 8-bit controller board recommendations by Ismangil	2,466	11	11/09/2017 07:32PM Last Post by JustSumGuy
	IDEX and IDE...Y? by PtitLu	2,275	7	11/07/2017 02:57PM Last Post by prot0typ1cal
	Direction of z-axis by flydeprutten	2,003	6	11/06/2017 02:26PM Last Post by prot0typ1cal
	Ultimaker with hiwin linear rails by Vigilant	4,335	8	11/02/2017 09:54AM Last Post by MKSA

Page 9 of 20 Pages: