Subject		Views	Posts	Last Post
	3D printer on TinyDeal by Mate	763	10	07/19/2014 09:17AM Last Post by MrDoctorDIV
	Heated Bed Stopping by mccajoe	457	4	07/18/2014 11:05PM Last Post by dexterousfolder
	Wilson TS Build by verb.zero	1,609	5	07/18/2014 04:46PM Last Post by verb.zero
	CoreXY - How to - 2 print heads by hooo100	537	2	07/17/2014 02:17PM Last Post by MrDoctorDIV
	PTFE Bowden Tube fitting by jobzombi	7,002	30	07/16/2014 06:41PM Last Post by madmike8
	Rostock Delta build by flyingmoose	789	11	07/16/2014 06:23PM Last Post by sheepdog43
	Threaded rods vs pulleys for x and y axes by Andycb	763	4	07/16/2014 06:01PM Last Post by A2
	Editing Arduino Flavour by tony woollacott	377	2	07/16/2014 07:44AM Last Post by Traumflug
	Arduino over heating..still! by cool2print	1,705	5	07/15/2014 10:32PM Last Post by jbernardis
	slic3 r support by tobig11	1,004	6	07/15/2014 03:31PM Last Post by KingRahl
	not getting a reading from heated bed thermistor. by josste	430	4	07/15/2014 12:35PM Last Post by josste
	RAMPS Power Terminals by Wisar	1,126	4	07/15/2014 09:10AM Last Post by 3D-ME
	Looking to build DLP Printer using Prusa i2 parts by kickinthethroat	442	2	07/15/2014 04:07AM Last Post by A2
	RAMPS thermistor and endstop connectors by foul_owl	333	4	07/14/2014 05:53PM Last Post by Paul4865
	Heating bed causes RAMPS to overheat and cut power by dexterousfolder	490	5	07/14/2014 04:40PM Last Post by Kurzaa
	steppers grunting by 65c10restomod	454	3	07/14/2014 04:35PM Last Post by Kurzaa
	Printupy DualX - Anyone got one of these? by thepest	1,292	1	07/14/2014 11:37AM Last Post by thepest
	Months of printing, then suddenly MAX TEMP exceeded on hot end by DoctorMike	847	5	07/13/2014 07:06PM Last Post by jbernardis
	gcode to left nozzle/z axis by EEstudent	1,194	3	07/12/2014 03:46PM Last Post by EEstudent
	Reprap RAMPS by Yaro	394	2	07/12/2014 09:31AM Last Post by vreihen
	3d pen by faz	452	3	07/11/2014 12:30PM Last Post by faz
	Motors won't move, very annoying by gcarron	392	2	07/11/2014 09:58AM Last Post by drmaestro
	Hi. Need newbie advice please. by rnprinter	456	5	07/10/2014 03:54AM Last Post by EEstudent
	Magma Hotend by novato	867	4	07/09/2014 09:05AM Last Post by bytemedwb
	Modifying the Z assembly by drmaestro	573	6	07/09/2014 08:01AM Last Post by drmaestro
	Edit running G-code in Repetier by sidhabo	473	1	07/08/2014 04:30PM Last Post by sidhabo
	Will activated charcoal filters remove UFPs from printing? by foul_owl	662	4	07/08/2014 02:26AM Last Post by Ralf
	Axis Barely Moves by erkall77	504	5	07/07/2014 10:24PM Last Post by waitaki
	Best printer by [email protected]	440	1	07/07/2014 05:04PM Last Post by [email protected]
	mk2b heat bed 24 v, only half heats up by BillC	719	3	07/07/2014 07:01AM Last Post by Ralph.Hilton