Subject		Views	Posts	Last Post
	Prusa I3 question about power supply by strk	345	5	01/02/2014 08:20PM Last Post by strk
	Extruder gears by printer_man58	501	5	01/02/2014 07:58PM Last Post by rogerclark
	Cooling fan suggestions for Mendel by JohnC	556	3	01/02/2014 06:34PM Last Post by JohnC
	need Ideas as not enough extrude from hotend by myk68	677	7	01/02/2014 06:02PM Last Post by myk68
	Hot end temperature problem by Jiten	745	6	01/02/2014 04:32PM Last Post by Jiten
	Extruder/Hot End problems by KD0SKH	512	4	01/02/2014 12:39PM Last Post by KD0SKH
	Issues with slicer. Please help! by Bigq30	463	5	01/02/2014 09:15AM Last Post by bytemedwb
	First Build Questions by BlaiddDrwg	651	9	01/02/2014 08:11AM Last Post by bytemedwb
	First build teething problems: Z-axis out of sync by Clydesdale	2,635	10	01/01/2014 03:50PM Last Post by uncle_bob
	Teacup firmware on Atmega128 for my Mini-RepStrap by Buzo	959	4	01/01/2014 09:35AM Last Post by dewasurya
	Shattered Thermistor Bead by JayTrinity45	1,026	6	12/31/2013 05:52PM Last Post by A2
	MK2 Heat Bed causing power to shut down by clanhenry	735	2	12/31/2013 05:34PM Last Post by lazzymonk
	Easier extraction from heated bed? by kfootball15	592	9	12/31/2013 07:44AM Last Post by Nununugent
	Out of control hot end temperatures by Yvan	917	14	12/30/2013 11:07PM Last Post by Yvan
	i need some advice by makovai	529	5	12/30/2013 08:13PM Last Post by vinmicgra
	What is the smallest practical XY step size? When does accuracy become overkill? by SamS	2,644	19	12/30/2013 07:54PM Last Post by uncle_bob
	SmartRap and the Benefit of a heating bed? by kfootball15	920	4	12/30/2013 07:53PM Last Post by uncle_bob
	What is the thinnest layer height? by Nununugent	875	5	12/30/2013 03:37PM Last Post by BlackDragon
	Printing from an Ipad? by kfootball15	2,318	13	12/29/2013 04:46PM Last Post by kfootball15
	Heatbed mystery by TheLizards	852	14	12/28/2013 03:03PM Last Post by TheLizards
	Infill Calibration Help by screamnAbdab	1,110	10	12/28/2013 10:40AM Last Post by neilrudd
	Z axis Fails to Rise when printing by KeenanKon	555	3	12/27/2013 01:31PM Last Post by Yvan
	Extruder issues... by btmeyer810	521	4	12/27/2013 11:02AM Last Post by uncle_bob
	Makerware broke RepG? by MrBaz	578	4	12/27/2013 09:09AM Last Post by MrBaz
	Design Software by Nununugent	736	10	12/26/2013 10:07PM Last Post by zvonimir
	12V vs 24V by epicepee	5,880	24	12/26/2013 05:35PM Last Post by uncle_bob
	Jhead or Magma for a First Time Builder by Marksest	651	5	12/26/2013 05:29PM Last Post by uncle_bob
	Ned Help in Choosing Model by shan2	566	8	12/26/2013 12:38PM Last Post by uncle_bob
	Stepper motor problem (underpowered?) by Sazabi	4,207	6	12/25/2013 06:46PM Last Post by uncle_bob
	Hot end help by luillo1	373	2	12/25/2013 06:28PM Last Post by uncle_bob