Welcome! Log In Create A New Profile

Advanced

Firmware - Marlin

Everything about Marlin firmware : Discussions, questions, support and feature requests... 
Subject Views Posts Last Post

Marlin Firmware 1.1.0 Release

by Thinkyhead
2,361 3 05/05/2017 12:44AM
Last Post by Roxy

Voltage controlled extruder signal

by Pelzeb0b
646 4 05/04/2017 02:52PM
Last Post by Roxy

Newbie: change firmware to handle some sensors with arduino language code

by paulo_silver
413 1 05/04/2017 09:24AM
Last Post by paulo_silver

Marlin Diamond Hotend

by h4nc
1,813 6 05/03/2017 12:31PM
Last Post by [email protected]

not supported display help

by iamturbo1978
414 3 05/03/2017 12:03PM
Last Post by iamturbo1978

help with my marlin configuration.h Attachments

by aleyan
775 2 04/27/2017 11:05PM
Last Post by Roxy

K-type Thermocouple

by Chaparro1973
2,348 7 04/27/2017 04:32PM
Last Post by Chaparro1973

MKs base v1.4 no option in marlin for EEFB

by Picodeguyoh
1,964 7 04/24/2017 06:52PM
Last Post by paboman

Compiling Marlin on Raspberry Pi (Raspbian Jessie)

by yonkiman
2,450 5 04/24/2017 02:08PM
Last Post by yonkiman

how to add button press to jump to a SubMenu in LCD please help.confused smiley

by gurmeet.athwal
668 2 04/23/2017 05:42PM
Last Post by Roxy

Completion percentage on full graphic lcd

by drmaestro
5,153 2 04/20/2017 09:18AM
Last Post by rrowan327

Marlin 1.1.0 RC8 - how to manually correct the probed Z height?

by icefire
1,085 4 04/18/2017 01:42PM
Last Post by Roxy

Marlin RC8 BLTouch and #define min_software_endstops false

by kkberg
1,119 1 04/17/2017 07:26AM
Last Post by kkberg

Dual stepper drivers on for single axis on Megatronics

by Outbound
627 5 04/15/2017 10:27PM
Last Post by Outbound

Is there an issue with Marlin Firmware RC8Bugfix Core XY Drifting to the left?

by Eddiie
571 1 04/12/2017 12:07PM
Last Post by Eddiie

Help needed configuring for two Z steppers Attachments

by rfresh737
2,452 15 04/12/2017 02:38AM
Last Post by o_lampe

Autolevel G29

by Sp-spain
479 2 04/12/2017 12:03AM
Last Post by Roxy

Z homing in wrong direction

by drewskeeh
1,500 3 04/11/2017 11:36PM
Last Post by Dust

Printer ignores G29 command.

by nansjes1
1,310 4 04/10/2017 12:35AM
Last Post by Roxy

Heater 2 pin to power additional fan

by MufaddalMarvi
1,054 3 04/07/2017 07:21AM
Last Post by MufaddalMarvi

Where to start auto bed leveling Marlin

by chasemn34
773 7 04/01/2017 08:13AM
Last Post by chasemn34

Marlin Users: Please cast a vote!

by Roxy
482 1 03/31/2017 11:24PM
Last Post by Roxy

Main Screen

by Suggy
448 2 03/31/2017 11:31AM
Last Post by Roxy

Implementing new kinematics

by .xack.
752 3 03/30/2017 06:29AM
Last Post by .xack.

Using the PS_ON_PIN as safety feature

by JanJans
946 4 03/29/2017 11:13AM
Last Post by JanJans

No variable speed with fan on D9 RAMPS 1.4

by rainswor
1,532 7 03/29/2017 01:12AM
Last Post by Roxy

Hibernate feature?

by iomaz
494 1 03/25/2017 04:32AM
Last Post by iomaz

Real problems with Ramps 1.4 and Marlin Attachments

by DOYT
1,945 11 03/24/2017 04:46PM
Last Post by DOYT

Dual Z steppers + Dual End stops problem

by Anehall
1,628 4 03/23/2017 05:55PM
Last Post by Anehall

Auto Bed Leveling ProbeOffset

by Sompy
743 1 03/22/2017 04:06PM
Last Post by Sompy