Bed material for nylon printing January 06, 2013 10:07AM |
Registered: 12 years ago Posts: 2 |
Re: Bed material for nylon printing January 06, 2013 01:54PM |
Admin Registered: 16 years ago Posts: 1,470 |
Help improve the RepRap wiki!
Just click "Edit" in the top-right corner of the page and start typing. Anyone can edit the wiki! |
Re: Bed material for nylon printing January 06, 2013 08:48PM |
Registered: 12 years ago Posts: 374 |
Re: Bed material for nylon printing January 06, 2013 09:24PM |
Admin Registered: 16 years ago Posts: 1,470 |
Help improve the RepRap wiki!
Just click "Edit" in the top-right corner of the page and start typing. Anyone can edit the wiki! |
Re: Bed material for nylon printing January 07, 2013 05:05AM |
Registered: 12 years ago Posts: 2 |
Re: Bed material for nylon printing January 07, 2013 11:38AM |
Registered: 13 years ago Posts: 62 |
Re: Bed material for nylon printing January 13, 2013 02:54PM |
Registered: 17 years ago Posts: 824 |
Re: Bed material for nylon printing January 13, 2013 04:17PM |
Registered: 12 years ago Posts: 560 |
Re: Bed material for nylon printing January 21, 2013 05:20PM |
Registered: 13 years ago Posts: 62 |
Re: Bed material for nylon printing January 21, 2013 09:55PM |
Registered: 12 years ago Posts: 939 |
Re: Bed material for nylon printing January 29, 2013 05:42PM |
Registered: 13 years ago Posts: 62 |
Re: Bed material for nylon printing January 29, 2013 06:40PM |
Registered: 12 years ago Posts: 939 |
Re: Bed material for nylon printing January 30, 2013 01:59PM |
Registered: 14 years ago Posts: 818 |
Re: Bed material for nylon printing January 30, 2013 07:35PM |
Registered: 12 years ago Posts: 939 |
Re: Bed material for nylon printing May 03, 2013 06:12PM |
Registered: 12 years ago Posts: 43 |
Re: Bed material for nylon printing May 03, 2013 09:12PM |
Registered: 11 years ago Posts: 137 |
Re: Bed material for nylon printing May 03, 2013 09:24PM |
Admin Registered: 16 years ago Posts: 1,470 |
Help improve the RepRap wiki!
Just click "Edit" in the top-right corner of the page and start typing. Anyone can edit the wiki! |
Re: Bed material for nylon printing January 08, 2014 12:22AM |
Registered: 11 years ago Posts: 7 |
Re: Bed material for nylon printing January 08, 2014 05:27AM |
Admin Registered: 13 years ago Posts: 2,569 |
Re: Bed material for nylon printing January 08, 2014 06:27AM |
Registered: 13 years ago Posts: 2,470 |
Re: Bed material for nylon printing January 08, 2014 08:54AM |
Registered: 11 years ago Posts: 34 |
Re: Bed material for nylon printing January 18, 2014 10:23AM |
Registered: 11 years ago Posts: 3 |
Re: Bed material for nylon printing January 19, 2014 11:07AM |
Registered: 11 years ago Posts: 3 |
Re: Bed material for nylon printing February 26, 2014 11:36AM |
Registered: 10 years ago Posts: 1 |
Re: Bed material for nylon printing February 26, 2014 12:49PM |
Registered: 11 years ago Posts: 553 |
Quote
Gulf
I just saw that the taulman3D web page has been updated with some more bed materials.
[www.taulman3d.com]
I found a printed circuit board at radio shack that was big enough to give a try but even on a small 0.75 in diameter cylinder the plastic was distorting the circuit board, it did stay down but the thin board did not have enough strength to keep a larger part from deforming the circuit board. Perhaps a thicker circuit board or one that was mechanically attached to a sheet of aluminum or something else.
The updated taulman3D page suggested Garolite (LE) from McMaster Carr, I am going to give that a shot and if it works well I will test it with PLA ABS and PC.
Anyone have any other ideas?
Re: Bed material for nylon printing August 25, 2015 01:50AM |
Registered: 10 years ago Posts: 65 |