printer halted when just click on the file to print from sd card
Posted by 3dprintnow
|
printer halted when just click on the file to print from sd card September 01, 2020 08:42AM |
Registered: 6 months ago Posts: 18 |
|
printer halted when print from sd card August 31, 2020 06:33PM |
Registered: 6 months ago Posts: 18 |
|
Re: printer halted when just click on the file to print from sd card September 01, 2020 08:57AM |
Admin Registered: 8 years ago Posts: 3,093 |
Please don't create multiple topics in different forums about the same subject 
Thank you.
http://www.marinusdebeer.nl/
Thank you.http://www.marinusdebeer.nl/
|
Re: printer halted when just click on the file to print from sd card September 01, 2020 08:59AM |
Registered: 6 months ago Posts: 18 |
|
Re: printer halted when just click on the file to print from sd card September 01, 2020 11:27AM |
Registered: 10 years ago Posts: 5,995 |
|
Re: printer halted when just click on the file to print from sd card September 01, 2020 12:52PM |
Registered: 6 months ago Posts: 18 |
lcd i use 2004
marlin version 1.9
config attached
about g-code the same file and the same sd card working good with another printer
And this video to see what happen
[drive.google.com]
Edited 1 time(s). Last edit at 09/01/2020 01:07PM by 3dprintnow.
marlin version 1.9
config attached
about g-code the same file and the same sd card working good with another printer
And this video to see what happen
[drive.google.com]
Edited 1 time(s). Last edit at 09/01/2020 01:07PM by 3dprintnow.
|
Re: printer halted when just click on the file to print from sd card September 01, 2020 03:08PM |
Admin Registered: 8 years ago Posts: 3,093 |
I don't think this is an SD problem. It's probably an instruction in the beginning of the gcode file causing the printer to halt. It can have many reasons.
There might be something connected up wrongly or a short or an endstop not connected or something like a heating error. There can be many reasons. I would inspect the hardware first.
http://www.marinusdebeer.nl/
There might be something connected up wrongly or a short or an endstop not connected or something like a heating error. There can be many reasons. I would inspect the hardware first.
http://www.marinusdebeer.nl/
|
Re: printer halted when just click on the file to print from sd card September 01, 2020 03:14PM |
Registered: 6 months ago Posts: 18 |
|
Re: printer halted when just click on the file to print from sd card September 02, 2020 07:54AM |
Registered: 6 months ago Posts: 18 |
|
Re: printer halted when just click on the file to print from sd card September 02, 2020 02:46PM |
Admin Registered: 8 years ago Posts: 3,093 |
I think I had this problem when my voltage regulator on the Mega was broken. It would work fine with USB but using SD card it would Halt. With my machine the reason was because of the servo I was using. The servo was putting too much strain on the voltage regulator. But I honestly don't have a clue what it could be. What kind of setup is the machine? It must have something to do with the LCD panel or power supply.
http://www.marinusdebeer.nl/
http://www.marinusdebeer.nl/
|
Re: printer halted when just click on the file to print from sd card September 03, 2020 12:16PM |
Registered: 6 months ago Posts: 18 |
Sorry, only registered users may post in this forum.