@Dave, thanks for your explanations! You are right I misunderstood the E value ... (learning never stops - thanks for the tip with extruder sizes in the comments). I made endless testparts, so I started to look directly at the G-code. Do I understand you right: the geometry G1 code will alwayse be same - I must work on the thickness of the perimeter that comes out of the nozzle. (my standard wivon Georg99 - Slic3r
@dmould: in General I agree with you. But still I do not understand the details: "default extrusion width" and "Layer height" define "plastic quantity" - that is clear. And plastic quantity is defined by the extruder speed E in G1. If I leave layer height unchanged, then only the "default extrusion width" influences plastic quantity, But the "default extrusion width" does not influence the extrudvon Georg99 - Slic3r
Now i checked further and find out it depends on the layer height: 0.1 mm G1:4.952mm = 9.904 (theoretical 10mm) 0.2 mm G1:4.905mm = 9.810 0.4 mm G1:4.810mm = 9.620 I am surprised about this dependency! Is there an explanation? Depends the perimeter diameter only on the layer height? What does then the nozzle diameter influence? Is it the speed for extruder? So with Nozzle diameter 0.4: X-4.952 Yvon Georg99 - Slic3r
I have made a squre model of 10mm size. the siz3r configuration is change to no top/button layer, no infill and only 1 Perimeter. (it looks like square fence). Default extrusion width=0 / repetier Host Extruder diameter 0.4 Now I can easily check the G1 movements. I have change the nozzle diameter in Slic3r from 0.4, 0.5, 0.6 ,0.7 but the movement stays always the same: 4.905mm from the center.von Georg99 - Slic3r
Ich komme jetzt doch nochmal auf das Thema zurück. Inzwischen habe ich doch 0.92 mit Controller zum Laufen bekommen! Ich benutze jetzt den "RepRap Full grphic Smart Controller" und drucke von SD-card. Der Controller hat eine Pausenfunktion, die ich manuell beim Print drücken kann und anschliessend wieder fortfahren kann. Funktioniert auch soweit gut. Kann ich die Pause auch direkt in den G-Codevon Georg99 - Software
I want to add a Fan. Generally I have problems to understand the link between the fields inside the configurator of Repetier und the Ramps 1.4 board. 1.In Repetier Configurator Fan Pin: "Heater 2 normally used for extruder 1" -- is this D9 on Ramps1.4? 2. For Z-Probe I have to define a pin in repetier firmware. Is the "Digital Pin 1" in the configurator the D1 in the AUX-1 block on board? Or whvon Georg99 - Repetier
Thanks for your input! I have a cooling - always running - fan the hotend. This is a second fan cooling the part itself. It is controlled with the repetier software. So I can wire it with (-) of D9 and (+) from Aux 12V, So it can be controlled, separately from the hotend cooler. Is this correct? For 1. and 3. I will go to the repetier forum ... maybe that is the second source ! Thanksvon Georg99 - RAMPS Electronics
I want to add a Fan. Generally I have problems to understand the link between the fields inside the configurator of Repetier und the Ramps 1.4 board. 1.In Repetier Configurator Fan Pin: "Heater 2 normally used for extruder 1" -- is this D9? 2. I want to use the (+) for the fan of D9. and (-) of the GND of the auxiliary connector 12V "12V Aux" (I think it is described D2). Is that ok? (I wantvon Georg99 - RAMPS Electronics
Ich kämpfe am gleichen Thema ... bist du weiter gekommen?von Georg99 - Software
Aha jetzt verstehe ich es besser! immer nocjh nicht ganz klar: du trägst im Code beispielsweise @pauseG91 Z100/nG91 X50/n ein. Wie macht dann der Code wieder weiter? woher weiss der Host die Pause ist vorbei? Noch eine Frage: Muss ich die @Pause vorher im Code eintragen - oder kann ich es unterwegs eintippen (da läuft der Code ja so durch..)? Der spontane Eingriff wäre nützlich beim Auftreten vvon Georg99 - Software
Dann benutzt du die 0.92 - ich muss die 0.91 verwenden da sonst der Grafik Controller dunkel bleibt ... Hast du den Grafikcontroller eim Eimnsatz? wie löst du die Pause aus?von Georg99 - Software
Danke fürs Antworten. Welchen Konfigurator meinst du? (Repetier-Host, Slic3r, Repetier-Firmware - ich kann norgends etwas mit Pause finden...) Wie löst man die Pause aus? Geht das mit dem grafikcontroller?von Georg99 - Software
Ich habe einen selbstgebauten Tripod, Repetier 0.91 und RepRapDiscount Full Graphic Smart Controller. Im Graphic Controller gibt es eine Funktion Pause. Wenn ich die benutze fährt er in die Z-Achse ins Bett. Wie kann ich eine Pausenfunktion integrieren? (Filamentwechsel) Idee:Ich drücke Pause, der Extrruder soll an eine Position fahren, ich extrudiere manuell bis das neue Filament kommt und danvon Georg99 - Software
Thanks for the tip! Especially the extrusion width (from 0 to 0.4) improved the behavior! (I thought it will be raed from the printer configuration of Repetier)von Georg99 - Slic3r
The Layer direct on the bed is perfect but the toplayer ist not filled!!! I have added the pictures of the last 3 Layers: layer63 filled - layer 64,65 only half filled. The result (teil.png) ist not so perfect ... Where is my error ... I played around - but could not change that behavior. top_infill_extrusion_width = 0 top_solid_infill_speed = 50 top_solid_layers = 3 Those 3 parameters seems tovon Georg99 - Slic3r