Show all posts by user
Printing issues ...
Page 1 of 1 Pages: 1
Results 1 — 15 of 15
I have a prusa i2. my circles are footballs. it is deforming on the y axis. can i get some help.
by
Hallestman
-
Printing
my heated bed and extruder refuse to heat up anymore they used to but don't now. i have a 12 volt 17 amp power supply but it doesn't work. any suggestions?
by
Hallestman
-
Controllers
i already got it fixed thank you though
by
Hallestman
-
Controllers
YUSS I fixed it! with your help of course. I put a fresh copy of sprinter on and it worked. thank you!
by
Hallestman
-
Sanguino(lolu)
the heater and thermistor for both the heat bed and the extruder head both work fine and read 26 degrees Celsius at room temperature. and i have re uploaded the firmware several times and changed some variable i believed caused the problem to no avail. I am using sprinter firmware
by
Hallestman
-
Sanguino(lolu)
so i tried a new power supply it was a 250 watt 12volt-14amp and the motors twitched just as much as with the other power supply
by
Hallestman
-
Sanguino(lolu)
i am building a prusa mendel i3 with sanguino 1.3a and everything was working perfectly when all the motors decided to stop working. whenever i use the manual controls with repetier host all the motors do is twitch in all directions. they where working fine before. i am using sprinter firmware i just re did all the wiring to see if it was that but it wasn't. Any suggestions?
by
Hallestman
-
Sanguino(lolu)
so i was dry printing with my prusa mendel i3 today (sanguino 1.3a) and my y axis stepper motor got hot so i turned the entire printer off when it cooled down and i powered on again all the stepper motor would do is twitch. please help. any help is help.
by
Hallestman
-
Controllers
capn thank you so much it works perfectly im setting up to do a dry print right now
by
Hallestman
-
General Mendel Topics
I am building a reprap i3 with sanguino electronics and i cannot get the end stops to work at all. i have them all wired up like in schematics but the do no register all the time. sometimes they do register sometimes they don they are very temperamental. any and all advice would be awesome.
by
Hallestman
-
General Mendel Topics
I have Slic3r 0.9.9 (64 bit) installed on my computer (windows 7 64 bit) in my program files folder. every single time i attempt to export g code it gets stuck on "Processing triangulated mesh" and then the program starts working. Is it my error,what can I do to fix it, please help.
by
Hallestman
-
Slic3r
I was wondering if stepper drivers are absolutely needed with sanguino 1.3a because I currently cannot run my stepper motors and i cannot find any reputable information
by
Hallestman
-
Sanguino(lolu)
Ihave one stepper motor directly soldered to my sanguino. I am running Marlin with Pronterface but i cant run the motors using pronterface at all. when i attempt to use the motor control in Pronterface no command show up on the box in the right. I have sanguino 1.3a and the latest pronterface.
by
Hallestman
-
Sanguino(lolu)
I am testing my stepper motors with my sanguino board before i attach it to my printer but i keep on getting this error "Printer stopped due to errors. Fix the error and use M999 to restart. (Temperature is reset. Set it after restarting)" and the hotend thermistor says that the temp is 478 all the time and i even connected the thermister and it still says that. Has anyone had this problem pleas
by
Hallestman
-
Sanguino(lolu)