Show all posts by user
Printing issues ...
Page 1 of 1 Pages: 1
Results 1 — 9 of 9
Hi all,
I have a problem with my printer.
It's a custom P3Steel 30x30x20, with a SKR 1.3 / TMC 2208 UART / Marlin 2.0.2 (updated few days ago), with 1 stepper motor for Dual Z axies motors, in stealchop mode.
My problem is that the Z axies motors doesn't seams to have the same speed. It's very hardly noticeable, doesn't impact on small height print /move, but as soon as i make long prints, wi
by
lezabour
-
Firmware - Marlin
Hey
Thanks for answers
My marlin speed is:
#define DEFAULT_MAX_ACCELERATION { 5000, 5000, 50, 5000 }
#define DEFAULT_ACCELERATION 2000 // X, Y, Z and E acceleration for printing moves
#define DEFAULT_RETRACT_ACCELERATION 2000 // E acceleration for retracts
#define DEFAULT_TRAVEL_ACCELERATION 2000 // X, Y, Z acceleration for travel (non printing) moves
Concerning the "
by
lezabour
-
Printing
Hi all,
Really need your help with a speed problem that make me crazy...
I have a Prusa I3, with Marlin RC BugFix on it, i'm also using Slicer Prusa Edition + Host Repetier (or Octoprint depend
EEprom is disabled.
I have a problem that i can't identify with my printer, about the printing speed.
I configured Slicer to with different speed to make tests.
But no matter what i do the printing s
by
lezabour
-
Printing
Ok, i tryed with faster printing, 40mm/s, 50 and 60
it's always worth ;( best result was with the 10mm/s
any other idea?
thanks for help
by
lezabour
-
Printing
Hi,
I have a Geeetech Prusa i3 Pro C (dual extruder) + Host Repeatier + Slicer. I'm pretty new (2 months that i have a printer)
I managed to solve almost all my problem and improve a lot the printing quality, but i still have a lot of difficulties with bridging
All the bridge elements are never straight, always bending which cause bad quality printing;
I have try to change the bridge speed (a
by
lezabour
-
Printing
Thx for answer,
I have seen this post,It need to solder on the board, which i rather not do. that's why i ask without soldering... i
There are several pins available on the board so my question is can we do that without the soldering
Normally we could use one of the FAN pin and connector available on the board, no?
thanks for help
by
lezabour
-
Prusa i3 and variants
Hi,
I'm having a hard time to make the auto bed leveling work.
I have a geeetech prusa I3 pro C, with a GT2560 (Rev A) control board.
I have a SG90 servo that i want to use for the auto bed leveling, and move the probe.
But with the GT2560 i don't find how to connect the servo to the board.
I tryed the following:
- use the FAN PMW Pin (it seams to be A7 so 7)
- use the Fan 3 (not used) Pin.
by
lezabour
-
Prusa i3 and variants
Hi,
I have a geeetech prusa i3 pro C , since 1 month now, and still have problem for calibration.
I add the auto bed leveling, so it would be easier to calibrate, but not so much
I use an inductive sensor (LJ18 A3-8-Z/BX sol - 36 V 8 mm) and a sensor mount without servo. I add an aluminium paper from kitchen beetween the Bed and the Glass. Sensor work fine with this configuration.
I use Hos
by
lezabour
-
Reprappers