Show all posts by user
Page 1 of 1 Pages: 1
Results 1 — 14 of 14
Just try the new release slic3r 1.2.0 version. it is required to set the bed shapes of printers. I have two delta, one standard mini kossel and a double sized one.
The standard mini kossel settings are ok. But when I try the larger one, every time when i choose circular bed shape and choose a large diameter, e.g. 300mm
after save and open the bed shape dialog agian, it is automatically changed t
by
shaqiu
-
Slic3r
I use the up to date repetier firmware from Github and my printer is ramps1.4 controlled delta(mini kossel). I'd like to try the sd_pause function during the printing, the printeris actually paused after run a few commands, and go to the wait postion. But after that I can't resume the printing with continue menu item. And Even wrose, all the data on SD card is corrupted. Don't know if other guys
by
shaqiu
-
Repetier
on the left of extruder temperature adjuster bar, just click the icon。
by
shaqiu
-
Repetier
Oh, I set build target as mega2560 and the above errors are gone :-)
by
shaqiu
-
Repetier
I downloaded the repetier-frimware source-code from . And try to buid it with code-blocks.
But I got the following errors
||=== Repetier, Simulator - Debug ===|
D:\src\ArduinoAVR\Repetier\HAL.h|482|error: cannot convert 'unsigned int*' to 'uint16_t* {aka short unsigned int*}' for argument '1' to 'void __eewr_word_m2560(uint16_t*, uint16_t)'|
D:\src\ArduinoAVR\Repetier\HAL.h|658|error: cast from
by
shaqiu
-
Repetier
you can just download the newest slic3r and directly replace the old one in repetier-host installed directory.
Everything will function as original
by
shaqiu
-
Repetier
Found where is the problem came from.
when I enable the retraction of slic3r , and checked the "wipe wile retracting" checkbox,
it generate Gcode like this
G1 X-27.837 Y5.703 F3840.000 E14.84644
G1 X-28.497 Y4.623 F3840.000 E14.47068
G1 X-28.927 Y3.443 F3840.000 E14.09783
G1 X-29.166 Y2.453 F3840.000 E13.79541
G1 X-29.571 Y0.182 F3840.000 E13.11032
G1 F1200.000 E13.01032
I guess it try to run
by
shaqiu
-
Repetier
Find the reason,
It caused by the "Wipe while retracting" settings, Just uncheck that checkbox and everything are OK.
So it should be a "bug" of the implementation?
by
shaqiu
-
Slic3r
When I enable the retraction of slic3r , the extruder always lost steps during retraction, but forward are correct。
after check Gcode, I found code like this
G1 X-27.837 Y5.703 F3840.000 E14.84644
G1 X-28.497 Y4.623 F3840.000 E14.47068
G1 X-28.927 Y3.443 F3840.000 E14.09783
G1 X-29.166 Y2.453 F3840.000 E13.79541
G1 X-29.571 Y0.182 F3840.000 E13.11032
G1 F1200.000 E13.01032
My retraction setting
by
shaqiu
-
Slic3r
I am trying to play with the slic3r retract settings and my extruder behaves strange. With the same setting, some times it reverse and forward ok, but
some times I heard a sharp noise and the motor dosen't reversed ubt forward more distance. I used a geared motor with 1:13 a gearbox, so I think it
should not be a "insufficient torque" problem. After search the internet, I found some one mention
by
shaqiu
-
Repetier
I had built a mini-kossel delta printer and would like the fine tune the print quality. And I think the repetier wiki's "print quality article" is the best introduction on this topic.
Flowing the instruction on the article. I hope could change the K and L with the advance test cases. But I can't find it in the repetier-host software. Is it already removed?
Another question is I used a 128*64 LC
by
shaqiu
-
Repetier
This
#define ORIG_Z_STEP_PIN 46
#define ORIG_Z_DIR_PIN 48
is for Ramps 1.3/1.4
and
#define ORIG_Z_STEP_PIN 44
#define ORIG_Z_DIR_PIN 46
is the original Ramps 1.1/1.2 pin assignment. So be careful with your board version.
by
shaqiu
-
Repetier
Try the 0.9.5 version and same thing happens. I suppose it is something related with codepage. I am running a non-english windows.
Could any one please help us to solve the problem? thanks in advance!
by
shaqiu
-
Slic3r
I used replicatorG windows version and simply downloaded the pre-build slic3r as the slice engine.
The combination works well till the version 0.9.1. But when the ver 0.9.2 is out. I got the following error
Can't locate object method "add_object_from_file" via package "Slic3r:rint" at
d:/ReplicatorG/replicatorg-0039/skein_engines/slic3r_engines/windows/lib/std/cavaexecscript/slic3r-console.pl l
by
shaqiu
-
Slic3r