That is a simplified version of fusion (which i use) that is a simplified version of auto cad. The interface is similar. Anyhow, I also use 123, so please send it over :-)by Fpex - Ormerod
I am going to gove it also a try once i get a second one ... since I am not touching my flying wires ormerod till i get all crimps to recrimp everything :-)by Fpex - Ormerod
I would reflow the entire board if you have an oven or can get to oneby Fpex - Ormerod
There might be few 0.6 back in stock, you better ask T3Dp3Dby Fpex - Ormerod
My 0.8.5 is properly wired now and config.g ok. Thanks guys. I hate flying wires, but this is a temporary thing to see if my duet0.6 is broken Anybody has designed a case for the 0.8.5 (with and without 4x board)?by Fpex - Ormerod
A question, does the duet 0.6 has a ground plane or is is using just ground traces? If the latter, than i know what the issues is ... the crappy board ground is gone (probably damaged when my older bed broke). I truly hope not. UPDATE: I would like to thank everybody, it looks like my duet0.6 is the culprit. I am now printing with the 0.8.5 ... so far it is printing beyond few layers. If the prby Fpex - Ormerod
Thanks a lot! My older duet had the 1k, i assume the new duet has the 4.7k then. I always got confused on what came first,by Fpex - Ormerod
Guys, how can i wire up the stock RRP bed level sensor to this duet and why is that my ned and hot end temps are so wrong? Can somebody share a config file for this board? Thanksby Fpex - Ormerod
Good idea, but first i need ti solve me real problem ... :-( and I am hating the fact that the two duet are few differences making it difficult to easily swap in a way that can always go back.by Fpex - Ormerod
I am not homing. I let it do by the gcode, so explained. :-)by Fpex - Ormerod
In the RRP firmware T0 waited, though. Anyhow, this is not something that i ever considered a problem, but just a due to a change in firmware. I do like that the hot end is not fully ready when it goes for the skirt, so i changed my start code anyhow into M190 S80 G28 M83; G10 P0 S150 R210 M116 G10 P0 S235 R210 T0 My problem stays, I now looking at replacingby Fpex - Ormerod
The real problem is that my printer is stopping printing after few layers as if it reaches end of file. I tried all sort of things, the only thing left are using a different supply and a different duet, but I only have a duet 0.8.5 to swap. After that I have no idea what to do.by Fpex - Ormerod
M190 works, the problem is on the hot end. G10 with DC42 firmware does not force to wait. To be honest, it is a minor thing as i do not mind loosing the skirt a bit but avoid hoozing at home. BTW I have simplify but i never managed to have any useable code for the ormerod :-(by Fpex - Ormerod
The code is the form the standard RRP profiles for the ormerod and it worked fine with the RRP firmware. Not with DC42 one. I guess it is because there is a difference! What do you use for gcode? I use slic3r only for the ormerod because i did not managed to use anything else Anyhow, this is the least of my problems :-)by Fpex - Ormerod
I tried several codes, this is from the last one that failed The current codes on my cards are here ; generated by Slic3r 1.2.9 on 2016-02-01 at 20:01:09 ; external perimeters extrusion width = 0.50mm ; perimeters extrusion width = 0.50mm ; infill extrusion width = 0.50mm ; solid infill extrusion width = 0.60mm ; top infill extrusion width = 0.50mm M190 S80 ; set bed temperature G28 ; homeby Fpex - Ormerod
i removed the external regulator to no avail. The prints et stuck and they are treated as end of file (the X axis gets homed and the printer is idle, even if all motors are locked) Also, but not sure this is normal with DC firmware, the print starts without waiting for the hot end to reach temperature.by Fpex - Ormerod
Thanks. I dismounted everything and I will use both ATX a d LED supply (since I have a 850w ATX in house to check on load). If it fails, I will try to connect a duet 0.8.5 even if at first glance it does not look straightforward. I want to get to the bottom of this !by Fpex - Ormerod
The panel due makes the regulator warmer, from very warm to hot. The mcu is a bit warm, and its temp does not change with the panel due presence. I have run several tests with bed or hit end off, and with your firmware and new web interface the printers gets stuck and the print is reported completed. Same with panel due. this is consistent with diagnostic indicating end of file. This is for meby Fpex - Ormerod
Thanks. I knew of it, it gets hot regardless of the panel due. I love panel due, pity the console ca not help me debugging the problem i am having. Honestly, i am kind of walking in the dark with this issue. if i had a spare duet 0.6 i would just do swap and see what happens.I have a duet 0.8.5, maybe i use that.by Fpex - Ormerod
Well, as i suspected printing from pronterface, web, slic3r, cura, printer face and even on OS X and windows, makes no difference. For some reason the printer did not get stuck on the original whistle.g ... but anything else i gave her, did not work. When i have time i will dismount the duet and remove the external regulator and see. I find it very unusual for it to get so hot that i get burned iby Fpex - Ormerod
I would like to try a,so another slicer, instead of slic3r. None of the simplify3d profiles i found works. Any idea how to get cura producing correct code ?by Fpex - Ormerod
That is one of the things i will be trying. before plugging in another supply Anyhow it is so how the dissipator on the regulator that i burn myself at touchby Fpex - Ormerod
This is really interesting, I always found the smoothie a better and more stable board also based on ARM. Make sure to make something modular and maybe use the same type of connectors are the smoothie.by Fpex - Duet
I am going to try a run with bed off. If this fails, I will try to remove the external 12/5v board (since it gets rather hot). If this fails, i will try to use a different supply. If this fails, I try to wire a duet 0,8,5 instead of the current 0.6 Ig this also fails, .... no clue. But all signs indicate a supply problem as a dip in supply on USB and SD reader could explain the pronterface failby Fpex - Ormerod