Search results
Create the page "Objects" on this wiki! See also the search results found.
- ...ing less electrical power to keep them heated. It also means that delicate objects being made are not shaken back and forth during layering, so that thinner s4 KB (650 words) - 12:12, 7 March 2013
- |description = Scanning of 3D objects ...Zealand) is doing a PhD that involves incorporating simple scanning of 3D objects into the Reprap toolchain to allow the user of the Reprap to do primitive 32 KB (336 words) - 08:13, 2 January 2015
- =Printed objects show brown/beige discolouration.=4 KB (646 words) - 15:35, 5 March 2012
- ...ition them in different places. Leave a gap of about 5mm between different objects to be built. ...iew/Main/MultipleMaterialsFiles described here]) for saving collections of objects positioned on the machine's build base.18 KB (2,265 words) - 15:59, 24 August 2015
- ...ess the same - see below). Then you can flip between the two when you load objects to build. The colour of objects made by the material in this extruder in the graphics window.27 KB (4,238 words) - 14:46, 26 November 2011
- ...Blender to modify the exported STL to enable Reprap host software to print objects.14 KB (1,817 words) - 05:52, 21 January 2015
- ...hnik parts -- [[FTIStrap]] is the first RepStrap to succeed in printing 3D objects14 KB (2,005 words) - 09:54, 15 June 2020
- ...ch team that came up with wire print found they could print 3D sketches of objects in on ly 8% of the time. What I would like to do is sightly different from9 KB (1,527 words) - 05:49, 26 March 2015
- The original Mendel Y bed upon which printed objects are deposited requires complex shapes to be cut out and uses rather a lot o5 KB (870 words) - 22:59, 27 March 2012
- Blender is frequently used for arranging multiple objects to print in one batch. This can save a lot of setup time if you want many s ...) is joining the objects before export. Just make sure you've selected the objects you want to include in one STL.6 KB (1,094 words) - 06:40, 11 January 2015
- It wouldn't work for tall objects as they start cracking due to the warping stress. ...e carpets stick to the floor - That was virtually impossible to get of the objects.21 KB (3,936 words) - 10:31, 17 June 2016
- ...ess the same - see below). Then you can flip between the two when you load objects to build. ...set true, this causes the system to start plotting outline patterns around objects from in the middle of their hatch infill, using a few of the hatch lines to30 KB (4,700 words) - 15:25, 26 November 2011
- ...open. The one on the left side is a console with which you can set up the objects to be printed for printing and with the RepRap machine, you can also use in ...utton to the next object. Leave a gap of about 5mm each freely between the objects.27 KB (4,531 words) - 23:28, 13 February 2024
- Switch Mode Power Supply Transformer insulators ( ensure G code objects have solid walls in ABS) jreinhardt; you can use python, you can get a list of all objects from FreeCAD.ActiveDocument.findObjects()168 KB (26,821 words) - 07:28, 3 July 2023
- ...o you'll have to export your board/object as a PNG image first. For larger objects without very fine features 200-300 dpi is fine, but for circuit boards I us38 KB (6,028 words) - 23:58, 25 May 2020
- SUGGESTION: App Store for reprap? where you can browse for printable objects? Hopefully all open sourced.3 KB (540 words) - 21:24, 22 January 2014
- Some objects can be dumped to the device. It all depends on the number of curves. A cu29 KB (4,689 words) - 15:45, 4 January 2015
- ...chine at all. (and also I dont see a point to have ability to print taller objects on rapman. Or having bigger Z travel)9 KB (1,419 words) - 23:38, 13 February 2024
- In biology and medicine, equipment to measure and manipulate objects on the micron scale are relatively common - though these devices tend to be ...m several angles. These techniques are also useful for observing completed objects.13 KB (2,073 words) - 02:46, 4 May 2024
- ...ave a grain like wood. Even when printed with an infill rate of 100%, such objects are not quite as strong (in some directions) as others. Tests show that pri2 KB (290 words) - 08:21, 28 February 2019
