Subject		Views	Posts	Last Post
	ABS layers not sticking. by Scribble	1,906	12	03/25/2014 02:26AM Last Post by Ralf
	Test Firmware Failed by GreekPride91	414	9	03/24/2014 09:25PM Last Post by GreekPride91
	small printing help by nalby	408	3	03/24/2014 01:52PM Last Post by nalby
	Printed Cubes bowed in. by jaeg	1,209	19	03/24/2014 09:40AM Last Post by jaeg
	Three small robots. Give me your tips how to improve it! by calad	1,208	6	03/24/2014 04:04AM Last Post by calad
	Stringy prints by carmojos	683	9	03/23/2014 08:18PM Last Post by carmojos
	Consistent Y-Axis Drift can tell you what it ain't can't tell you what it is!!! by DrDave	1,302	7	03/23/2014 04:17PM Last Post by robr45acp
	Print Problems by Doug1	604	1	03/23/2014 12:44PM Last Post by Doug1
	Y axis is stopping after few movement... by 3D Printer Beginner	613	4	03/22/2014 03:48AM Last Post by Pat McD
	How do I fix this sloppy print? by cubedude76	1,884	6	03/21/2014 09:10PM Last Post by vreihen
	Can't figure out how to fix this. by rjweng91	476	5	03/21/2014 05:03PM Last Post by jzatopa
	Not enough retractions? by rjweng91	653	3	03/21/2014 02:47PM Last Post by rjweng91
	Heatbed Causing Disconnect When Turned On by equinox86	577	4	03/21/2014 09:00AM Last Post by equinox86
	Print going bad at higher layers - Mono Mendel by Sumeet	906	5	03/21/2014 01:10AM Last Post by Sumeet
	Print Size Issue by logiwan992	414	2	03/20/2014 11:47PM Last Post by cat.farmer
	Bad verticals and strings. Ideas? by saintcady	723	5	03/20/2014 03:38PM Last Post by rjweng91
	Poor print corners, but not everywhere! by Potapich	436	5	03/20/2014 03:15PM Last Post by Potapich
	Print fails after first layer - hobbed bolt starts slipping by dpalo	1,244	5	03/20/2014 12:39PM Last Post by randyf1965
	Printing object mirrored by Paul4865	1,780	3	03/20/2014 03:48AM Last Post by Paul4865
	cant write to printer after crashing the y-axis without the endstop in place by bdelf85	1,129	9	03/19/2014 10:09PM Last Post by bdelf85
	Extrusion Multiplier by ayouden	929	5	03/19/2014 06:54PM Last Post by NewPerfection
	Z wobble issue - I just can't figure it out! by geoffreyc	2,620	4	03/19/2014 09:57AM Last Post by Rotz
	Multi-part printing issues by thefuzzbl	1,288	16	03/19/2014 01:52AM Last Post by thefuzzbl
	PLA sticking to blue tape and glass by starmind001	603	4	03/18/2014 09:19PM Last Post by starmind001
	Random Extrusion Failure by sniporbob	3,110	11	03/18/2014 09:57AM Last Post by Wisar
	Blistering/Lifting on first layer by amrbekhit	4,563	12	03/18/2014 04:05AM Last Post by waitaki
	First print. by romon	406	1	03/15/2014 01:44PM Last Post by romon
	No extrusion during print by romon	1,860	11	03/15/2014 01:10PM Last Post by romon
	Layer Height 50% of actual value by bishupz1	706	8	03/14/2014 06:02PM Last Post by bishupz1
	Error Message Repeated/Not a functional board by GreekPride91	353	3	03/14/2014 09:33AM Last Post by GreekPride91