Welcome! Log In Create A New Profile

Elettronica e meccanica

Discussioni sulle parti elettriche ed elettroniche, motori, endstop, etc. Parliamo di struttura della stampante, pulegge, madreviti, boccole, viti trapezoidali, etc.

Page 49 of 54 Pages:

47 484950 51

Forum List New Topic RSS

	Views	Posts	Last Post
solenoide con arduino by maralb	1,244	4	05/30/2014 09:28AM Last Post by MagoKimbra
RAMPS 1.4 - Non si accende by XiaZ	1,324	5	05/28/2014 09:37AM Last Post by XiaZ
Marlin & Auto Bed Level by MagoKimbra	1,541	12	05/28/2014 09:31AM Last Post by Galeots
Come connettere un cavo Flat tra heatbed e Arduino Mega by bellami	1,308	5	05/28/2014 06:38AM Last Post by bellami
Problema spostamento layer by krossk2	2,590	10	05/28/2014 03:54AM Last Post by sertum
Arduino Due e RAMPS [Risolto] by amario57	840	9	05/28/2014 02:11AM Last Post by amario57
Richiesta chiarimento tipi di cinghie. by enricodare	1,996	3	05/24/2014 11:27AM Last Post by Ivan Bortolin
non riesco a stampare da SD (Pages: 1 2) by mdcompositi	3,119	38	05/24/2014 06:20AM Last Post by immaginaecrea
Regolazione Driver panucatt 8825 help! by fr4nc3sco	443	5	05/24/2014 05:19AM Last Post by maralb
problema asse z by alby199	1,414	10	05/23/2014 05:57PM Last Post by lexon
riparare Arduino by RomanelliAlessio	1,779	18	05/22/2014 08:15AM Last Post by RomanelliAlessio
Sostituzione barre asse Y by rdware	358	3	05/22/2014 06:31AM Last Post by rdware
alimentare Arduino da Power Jack. [Risolto] by RomanelliAlessio	2,444	23	05/21/2014 04:13PM Last Post by RomanelliAlessio
Repertiehost si blocca improvvisamente by Danio Bonello	420	3	05/21/2014 02:26PM Last Post by Nicola P
Differenza tra NEMA 17 da 0,9deg e 1,8deg by DogFight	1,727	6	05/21/2014 12:00PM Last Post by DogFight
Non riesco a stampare dalla SD [Risolto] by vrooom	1,510	25	05/20/2014 01:06PM Last Post by mdcompositi
nuovo approccio all'auto bed leveling... by enricodare	404	1	05/20/2014 10:25AM Last Post by enricodare
Problema con Asse X by monte.m79	375	4	05/20/2014 08:19AM Last Post by Nicola P
pulleggia motori stepper by DeAndreon	1,231	11	05/19/2014 01:22PM Last Post by lion_heart78
l'estrusore non si scalda(risolto) by nik89	1,049	6	05/19/2014 12:28PM Last Post by campe89
Prusa i3 rework: cinghia asse y by bilanciamist	723	4	05/18/2014 03:24PM Last Post by sipperton
problema con sonde temperatura by alby199	487	5	05/18/2014 08:51AM Last Post by alby199
problema megatronics 2.0 by apk656	978	9	05/17/2014 04:13PM Last Post by px200
PROBLEMI MOTORI!!! by zezze	904	8	05/16/2014 04:30PM Last Post by lexon
Elettronica da Cina by angelboss	410	3	05/15/2014 08:04AM Last Post by sipperton
ramps ... modelli e prezzi ... che confusione :-( by deltaforce	530	7	05/15/2014 07:59AM Last Post by sipperton
Prusa i3 - Tensionamento cinghie assi x e y by bolivazio	1,859	4	05/14/2014 08:40AM Last Post by immaginaecrea
Driver by tigranpollosjan	396	3	05/13/2014 07:04AM Last Post by Ivan Bortolin
Azteeg X3 Pro - Qualcuno ce l'ha? Opinioni? by Gordie	400	1	05/12/2014 10:28AM Last Post by Gordie
Problema Alimentazione RAMPS1.4 [RISOLTO] by rosario3dprt	2,929	8	05/09/2014 08:14AM Last Post by rosario3dprt

Page 49 of 54 Pages:

47 484950 51

Elettronica e meccanica

non riesco a stampare da SD (Pages: 1 2)