im trying to compile this but keep getting this error not sure what to change etc or where theerror is can you help Arduino: 1.6.7 (Windows 10), Board: "Arduino/Genuino Mega or Mega 2560, ATmega2560 (Mega 2560)" In file included from D:\3d printing\software and firmware\firmware\Marlintrists_calibrated\Marlin_created_17.11.15_for_lcd\Marlin_created_17.11.15_for_lcd.ino:35:0: sketch\Configurby trist077 - General
its also done dotted lines not solid at all on the perimeters as of the 3rd layer e3d v6 0.4 nozzel all clean fan on heatsink powered direct to power supplyby trist077 - Printing
as in photo starts from secand layer first layer perfect get solid lines then get dotted rough lines does so many solid then so many dotted over again till the end of the layer using pla 207degree simplify 3d 30% infill 1 perimeter prusa i3by trist077 - Printing
I checked all and it's calibrated will try printing with repetier see what happensby trist077 - Printing
using simplify 3d printing a bed leveling part ive corrected bed level 3 times and if i print centre the first layer is worse so bed level but still have a little bed nozzle touching in photo secand problem when infilling it does not go all the way to the right whats wrong see photos final part good apart from the inill not touching prrimeters layer 1 layer 1 layer 2 layer 3 final piecby trist077 - Printing
want to do auto bed leveling on my custom prusa i3 i have a 9g servo from my rc plane and a spare mechanical endstop would need to print mounts but not too much of a problem where do i wire servo to ramps 1.4 and where do i wire endstop too as most vieos just show mounting endstop theres a lot of videos out there that make it confusing need to know what to put in marlin too what good reliableby trist077 - General
The problem was the nozzle changed the nozzle and all 9ok so must have put too much heat on nozzle when cleaning outby trist077 - General
stated using simplfy 3d had some good prints using pla but last one carried on but not extruding anyway cleaned out nozzle etc and replaced went to reprint and it makes a mess and when its stationary theres ozzing all the time not sure whats gone wrong replaced thermistor still the same please help was getting into after all the problems was having tryed repetetier as well which was using laby trist077 - General
borrowed a copy and impressed but the objected i printer sthe solid straight line at the back has a empty line in the middle which makes it a little weak the infill does not seem to fill this bit if fills the sides ok this line would be on my x axis when printing on prusa i3 any ideasby trist077 - Printing
found the problem i had not quite got all the pins in the arduino board now screen works and endstops triggerby trist077 - General
hi all my arduino or ramps board decided to stop working so replaced with new one but cant get end stops to work replaced wire by wire from old board so sure there replaced correct 1st x axis miss one y axis miss one the z axis m119 says all open when open when i close any of them m119 still says its open i tryed a new endstop on x and still the same also cant get my reprap ful grapic smart cby trist077 - General
but i need something to hold the z axis belt as theres 2 bits through the back that hold the belt one each sideby trist077 - General
361244421051 seen this on ebay this is more orless what i have anyone know where can get in uk as want asapby trist077 - General
i have this clear acrilyc x z axis carier where the e3d v6 bracket bolts too has snapped the it has a hole in the middle for the tube from the extruder then on the back goes throght to holes that the belt fastens too its a czar desighn i was told when bought with acrilic cut parts the actual bit has snapped currenty on bench drying after glue ing will post photo soon and idea what the partsby trist077 - General
right hers the reprint the cube on more or less perfect a bigger tes large square with othjers on top bad quality (killed job on large square) the stepper moter for extruder i edited the podometer and its warm to touch like the others does not fel too hot also recalibrated extruder to 112 in marlin for 50mm filiment was 125 was not taking a full 50mmby trist077 - Printing
i did have a little knocking on extruder every so often thought it was because was to tight or loose so i turned pedometer a tiny bit clockwise lookin at board from bottom and the the ped at bottom so running a new print heres some pics tooby trist077 - Printing
yes fan on heatsink e3d v6 genuine is the extruder tension the bit that is drawing in the filiment also how do i check current thanks#by trist077 - Printing
as in pics one on left was without fan on the right with fan after first layer at 50 using repetier purple pla 220 0.3 no heat bed perimeters 35 speed all why do i get some smooth layers then further up i go get bad layers then settles smooth again then a messby trist077 - Printing
at the moment just about got pla running but as in picture every so orten the layer does not fully make comtact e.g little gaps where can break not tryed abs yet trying to get pla working first any ideas its a small part not tryed larger yet also in a previous post some one was talking about z wobble and checking lead screws what are these where are they still a novice printer learned a lot ofby trist077 - Printing
why does the 45 layer go funny when the rest okby trist077 - General
finally a little success swapped to usb and cura had to print a t 230 for pla to come through better but not perfect but better than sd print anywat tryed pronterface as what used before cura and lcd just could not get to extrude or print so thought would give repetier a try as could not work when first had had to print a small object after i had reet some settings and so far still printingby trist077 - General
yes will try computer next as reset configs diferent temps u blocked etcby trist077 - General
right tryed abs again but same put new e3d v6 nozzle and heat block on too all extrudes fine when i go on lcd and prepae extruder all comes out ok but when i click a print off lcd it takes ages for it even to start brim which is set to 6 rounds i n slicer and when the print itself starts from centre the layers are all messy not alighned and together the bed and z axis have been checked numeroby trist077 - General
i did think the pla was extruding slower was using cura and sd card will try with slicer on pla see what happensby trist077 - General
decided to try pla again today but a weird thing is i printed the same object abs and pla the pla is the purple in pic whys it prints lines apart where as abs was all together abs was 237 pla 200 all other settings sameby trist077 - General
sorted left it for a few hours put some heat on nozzle and used a magnet to retrieve drill bit must have been stuck by a little plastic now can see straight through nozzleby trist077 - General