Show all posts by user
Printing issues ...
Page 1 of 2
Pages: 12
Results 1 — 30 of 42
Hello thank for information yes I know it's not good
and even if I change it in marlin when I upload marlin it does not change.
moreover I encounter an issue when warming bed printer goes on error.
I found power supply is or not enough power full or has an issue.
I changed it and it seem to work better
I will test anew and keep you informed
by
Dgils
-
Firmware - Marlin
Hello Hello everybody,
I have a DELTA KOSSEL K800XL I change original board to a SKR1.3+TMC2226 (TMC2209)
I use marlin 2.1.x
I try to calibrate PIDTEMP and PIDTEMPBED.
I use pronterface to do it :
M503 to get ref of head and bed
result M301, M304 respectivelly for head and bed
M301 E0 S210 C8 to warm at 200
I get P I D value and I enter them with command M301 Pxx.xx Ixx.xx Dxx.xx
update of t
by
Dgils
-
Firmware - Marlin
Hello all,
visual studio - marlin
I just received last version of PIO update Core 5.2.2·Home 3.3.4. since this upgrade I receive this error message :
ERROR: Old files fell into your Marlin folder. Remove ultralcd_DOGM.cpp, ultralcd_DOGM.h and try again
If I try to remove them I receive numerous message of error.
I do not know where to find this 2 files up to date. And I do not understand why
by
Dgils
-
Firmware - Marlin
Oki I just tested.
Nothing changed. No move from motor.
any new idea to make it work ?
by
Dgils
-
Controllers
thank you... at least I progress.
Ok I activated it, but not tested for the moment not on site where the printer is.
when compiling, I get this error message that is not blocking but is in warning :
'void print_es_state(bool, const char*)' defined but not used [-Wunused-function]
is it because I have physical endstop and SPI mode do not use it ?
if I understand good SPI mode use motor resust
by
Dgils
-
Controllers
Hello,
I changed my 2560+ramp1.4+a4899 with a SKR1.3+TMC5160
I follow instruction from btt to make setup on SKR1.3+TMC5160
I use visual studio for diferent version of marlin 2.0
everytime I compile with success
I succeed in transfert to board.
here is issue I have : I can not make work motors.
I made different test.
try with different marlin. version originale V2.0.6x V2.0.9.1 V2.0.9.2 even
by
Dgils
-
Controllers
Hello,
i tried the search function.
I search my pseudo, it's working I get all messages I posted
I try to search
SKR
skr
Skr
skr 1.3
and did not get any result
I try it from different browser same issue
I try with some other word same issue
i try directly in folder where I can see skr word same issue
am I the only one to encounter this issue ?
by
Dgils
-
Administration, Announcements, Policy
Hello,
sorry for the delay in answering... after a long time I did not touch printer because too demoralised with this printer I came back and found issue... I connected on the wrong port. E1 instead of E0.... so it's working now thank for your help.
In the meantime I still can not print extruder is not enough strong to push pla. I need to turn screw on A4899 to put higher voltage but as i do n
by
Dgils
-
Printing
Hello,
Sorry for the delay,
For information, issue seem to connected with A4988 I need to turn small screw to put more voltage in motor. But i do not have ref of motor or did not find it to calculate voltage I need.
In the meantime, I bought an SKR1.3 + TMC5160.
I changed board.
I have some new issues but anyway thx for your help with this
by
Dgils
-
Delta Machines
Hello,
I have an SKR1.3 + TMC5160 for a delta kossel.
marlin is 2.0.9.1
in the menu I do not have in menu function to move x y z axes. this option are missing.
when I try to make an home function few sec after printer goes on halt and I need to reset it.
I would like to use pronterface with usb cable to use move function but proterface does not find any printer even if windows can see the memory
by
Dgils
-
Firmware - Marlin
Hello,
Did you solved issue ?
I have same issue.
even if windows can see the com5 and can access memory card on board, pronterface does not reconise my SKR 1.3.
by
Dgils
-
Controllers
Hello,
I have an SKR 1.3 I have some problem of setup but I have not trouble with board itself. Mayby your power supply 24V is not good to much/not enough voltage, maybe parasite or noise on 24V signal ?
by
Dgils
-
Controllers
So I finally finish with setup of my delta.
i have delta kossel K800xl + marlin 1.1.9.1 (last one) + alumimium bed
I use cura 4.8 (last version up to date)
distance between bed and nozzle is like a piece of paper thin. mean I tune z heigh correctly
I tried to print a cube 10mm side :
here are trouble I encounter when printing :
-at the begining pla do not stick to bed.
-I try to pass from 6
by
Dgils
-
Delta Machines
125 BAUDRATE 250000
most of the time 115200 is better, less trouble
547 DELTA_RADIUS 123
do you have a print area of 246mm diameter ?
I have a kossel k800xl and mine is 280 mm diameter
remove bed leveling linear
delta use G33 for this.
by
Dgils
-
Delta Machines
there is no noise at all on the motor and I tried to cross/uncross cable on board connector : No change
Maybe, if on the AT2560 I can manage a second extruder on another connector. maybe I can use this ?
problem is I do not know how to change marlin to have extruder 2 as default
and if I need to change driver position on the board ?
by
Dgils
-
Printing
Hello,
thank for information,
i have done as you said, but wanted to know why I encounter this issue.
So now I will say it's solved.
Problem is now I have extruder motor not turning.
I open a new post for this. with all what I already done
If you have good tips, like maybe inverting extruder 1 and 2 even if I do not have a second extruder...I take
by
Dgils
-
Delta Machines
Hello,
I have my extruder not turning at all.
For information I test it with warming and without warming head.
motor does not turn.
Before it was making strange noise but not anymore and do not turn
I tried :
change cable
change motor
move extruder from pronterface
move extruder from printer itself without success
I have a delta kossel K800xl mega2560+at with unknown driver the less expensive I
by
Dgils
-
Printing
oki,
what I have done, is this :
start with your marlin advise marlin1.1.9.1
use config+adv.h file
modify them as they do not integrate the minimum of delta setting....(none of all marlin have config.h setup for a delta....)
FOr info I try to dl config +adv h you provided me as a link, but there is no dl option, I need to copy them in a file and rename file.
initialise eeprom
G33 for delta calibr
by
Dgils
-
Delta Machines
I made an initialise eeprom
now i have menu move on axes XY and move on Z plus some other option but still not calibrate axes Z
by
Dgils
-
Delta Machines
if I change the height in marling it's not taken in count when I upload marlin in printer
by
Dgils
-
Delta Machines
maybe someone with a delta kossel... maybe not a xl can send me config + config adv file
by
Dgils
-
Delta Machines
Hello,
yes they are triggered
SENDING:M119
Reporting endstop status
x_max: open
y_max: TRIGGERED
z_min: open
z_max: open
>>> m119
SENDING:M119
Reporting endstop status
x_max: open
y_max: open
z_min: open
z_max: open
>>> m119
SENDING:M119
Reporting endstop status
x_max: TRIGGERED
y_max: open
z_min: open
z_max: open
>>> m119
SENDING:M119
Reporting endstop status
x_max:
by
Dgils
-
Delta Machines
for information if I use config .h of the one I create the topic, I have the menu calibrate ... but I also have issue
by
Dgils
-
Delta Machines
it's enabled :
// Enable DELTA kinematics and most of the default configuration for Deltas
#define DELTA
#if ENABLED(DELTA)
// Make delta curves from many straight lines (linear interpolation).
// This is a trade-off between visible corners (not enough segments)
// and processor overload (too many expensive sqrt calls).
#define DELTA_SEGMENTS_PER_SECOND 160
// Convert feedrates to a
by
Dgils
-
Delta Machines
i added 2650 in the name
real name is :
Marlin-bugfix-1.1.x
ok I dl marlin 1.1.9.1 with your link.
Problem in menu there is no more calibrate Z option after auto home...
by
Dgils
-
Delta Machines
oki, I took marlin 1.1.9.1 + config and config adv from kosell XL.
grrrr, now the homing act strangelly. only 1 motor going down as it should goes up for homing....arg
by
Dgils
-
Delta Machines
I just checked.
it does not take count of it, it seem to go down always 16cm quickly first and slowly and printer reboot
by
Dgils
-
Delta Machines
Page 1 of 2
Pages: 12