You should not be able to wiggle it by hand. Anything tighter than that will deform the wheels though.by Srek - Mechanics
This usually happens if the hotend parts are not screwed together tight enough. They basically seal by deforming slightly. Depending on the hotend it is a delicate act to find the point where it is tight enough without ripping the heat brake.by Srek - Printing
I‘m printing ABS for 8 years now and have not noticed anythingby Srek - Safety & Best Practices
QuoteBoKKeR Oh God No! Please check the original products link. It consists of 2 and magnetic Sheets. One you glue down on the bed and one that you put on top. The one on top is sticking to the one on the bottom. I printed on the one on the top but it started to wrap at the edges. I would say that the top sheet has lost its magnetism That’s whati meant. You need an additional top layer on the topby Srek - Printing
Ja, Stepper sind über den Strom limitiert, nicht wie brushed Motoren über die Spannung. Eine Obergrenze für die Spannung gibt es natürlich auch, die liegt aber weit jenseits von 24Vby Srek - Elektrik & Elektronik
Ich würde Stepper, Bett und Hotend mit 24V betreiben. Bei meinen Druckern setzte ich da zwei mal RUMBA und ein mal RADDS ein. Für 230V Heizung ist eine Silikonmatte die einzige sinnvolle Lösung, das unter eine mindestens 5mm dicke gefräste Aluplatte sollte tun. 30x30 für ein Y bewegtes Heizbett ist aber schon grenzwertig, das ist nicht nur massig sondern nimmt auch viel Platz weg, der Drucker wiby Srek - Elektrik & Elektronik
You used a magnetic foil directly to print on? I can see why this went wrong. The printhead will heat up the foil well beyond what it is meant to withstand and it will loose magnetism. You always need a top layer, be it FR4, PEI, steel, Buildtak or whatever.by Srek - Printing
Another thing, the double sided tape used on that is only rated for 90°C long term, you should try to use 3M 9473 instead.by Srek - Printing
Was it glued to the bed? I am using magnetic setups as well and never observed anything like this. While the magnetic foil is pretty soft and can deform easily when hot it does not exert a lot of force. Correctly glued it shouldn't warp at all.by Srek - Printing
The size of the bend could just be a few 1/10mm and would easily produce that wobble. As dc42 said. Check the pitch of the rod against the wobble. If they match it is z-wobble. Basically no z rod is absolutely straight. Usually you try to minimize the bend and compensate for the rest that is left by using an anti z-wobble solution (check thingiverse). Even if you were to get a perfectly straightby Srek - Reprappers
That looks like massive z wobble. Is your z rod bent?by Srek - Reprappers
Ich habe eine ganze Zeit an Bowden Extrudern für flexible Filamente gebastelt und auch zufriedenstellende Ergebnisse hinbekommen. Am Ende ist der Aufwand aber hoch und der Einsatz in der Praxis etwas umständlich Hier ein paar Videos mit dem Spezialextruder Ich habe auch mal eien Bulldog dafür umgebaut Das Filament war aber eher zäh elastisch und daher weniger problematisch zu drucken Am Ende hby Srek - Allgemeines
Jain. Wo kommt der gcode her, wie wird er generiert? Normalerweise reicht es im Slicer die Bettemperatur auf 0 zu setzten, dann wird entweder M140/190 S0 gesetzt oder erst gar kein code dafür erzeugt. Dann brauchst du auch sonst nichts ändern. Wenn du aber nicht verhindern kannst das der code geschrieben wird dann hilft es auch nichts das in den Header zu setzen, da danach ja der erzeugt Code komby Srek - Druck- und Heizbetten
Im gcode händisch M190 und/oder M140 auf 0 setzen.by Srek - Druck- und Heizbetten
Wow, das Angebot ist noch von damals als RRD probiert hat über Ali zu verkaufen. Merlin ist übrigens wirklich ein Haustier, das Hotend wurde nach meinem schwarzen Kater benanntby Srek - Offtopic
Das Ausrichten des Heizbettes habe ich mir einfach gemacht. Ich habe eine Halterung für eine Messuhr gedruckt die ich statt des Druckkopfes einsetzen kann, damit gelingt das Ganze sehr schnell und einfach.by Srek - Druck- und Heizbetten
Ich würde immer mindestens 10% überdimensionieren, das 250W Netzteil käme für mich alleine deswegen nicht in Frage. Ansonsten sind Schaltnetzteile halt Schaltnetzteile, manche sind besser, manche schlechter. Ob sie als LED Netzteil oder nicht beschrieben werden ist dabei egal. Auch der Bekanntheitsgrad der Marke ist leider kein sicherer Qualitätsindikator.by Srek - Elektrik & Elektronik
Nein, ich stelle im SLicer 0mm Distanz ein und stelle den Abstand physikalisch auf 0.1. Die Fühlerlehre verwende ich genauso wie papier, nur haltbarer und präziser.by Srek - Druck- und Heizbetten
Vorzugsweise dünnes Papier (<80g) und dann so einstellen das man gleichmäßig Widerstand fühlt wenn man es unter der Düse bewegt. Ich mache es aber lieber statt mit Papier mit einer 0.1mm Fühlerlehreby Srek - Druck- und Heizbetten
Folien sind da, vielen Dank!by Srek - Schwarzes Brett
Wenn ich Teile in ABS drucke hilft Aceton Bedampfen kleine Poren zu schließen oder Teile sauber zu verbinden. Ansonsten mus sich sagen das ausser Kunstharz nicht viel gut für mich funktioniert hat. Sugru hat in einigen Fällen noch gute Arbeit gemacht.by Srek - Allgemeines
At 70 bucks the wallace is as cheap as it gets. Chances are it will work but will require a lot of fiddeling until it does. Due to its flimsy construction you won't be able to print very reliable or precise. The whole RepRap idea has come to a standstill after the Mendel has been turned into what are now the Prusa and it's many clones. While the Prusa still has quite a few printed parts it does rby Srek - General
Basically any controller will do and the default extruder is afaik a Wade. The printer is a bit outdated though, why not build a more current one?by Srek - General
Ich wäre gerne mit 2 Stück dabeiby Srek - Schwarzes Brett
Wie hoch ist denn die Innentemperatur der Kammer? Ich würde versuchen sie anzuheben.by Srek - Allgemeines
My direct drive extruder works fine with Nema 14 as well. I used them in the past but had problems. Later it turned out the problem was a design issue and that Nema 14 is sufficient. Maybe i switch back to it at some point, vut currently there is no need.by Srek - General
I still have a wade running in my old machine (8 years now) and it does a very good job, even though its strength is wasted on the 1.75mm filament and the Merlin hotend. With 1.75mm filament there is no real need for a geared extruder, yes, the theoretical resolution is better, but i can't say i have seen that this ever mattered to me. At Protoworx they use simple direct drive extruders with a Mby Srek - General
I can see the use of a dual hobbed extruder to minimize the damage to the filament, but tbh a well adjusted idler strength will do the job 99% of the time just as good. For me the two most important things to maximize extruder strength and speed are exact guidance of the filament, no kinks around the hobbed idler or similar, and a hotend that requires minimal pressure.by Srek - General
For me a reason to not do it is that it is unnecessary. I have thought about filament transportation with multiple points of contact, but in the end they did not offer any advantage. A well designed classic direct drive will develop enough force for well over 100mm/s. Another issue is size, such a setup will be larger than a single point of contact drive.by Srek - General
0.2mm und "blutiger Anfänger" sind zwei Sachen die man nicht mischen sollte. Der echte physikalische Unterschied bei der Extrusion ist größer als die meisten Leute erwarten und es wird nie einfacher. Wenn du irgend welche Verstopfungsprobleme mit 0.3mm hast dann sind 0.2mm das Letzte was du willst. Wenn du keinen zwingenden Grund hast auf 0.2mm zu gehen dann lass es. Im Gegenteil eine 0.4mm Düseby Srek - Software