Welcome! Log In Create A New Profile

Advanced

Mechanics

Discuss any sort of mechanical stuff here: positioning systems, gears, extruding methods, etc. 
Page 1 of 35    Pages: 12345NextLast
Forum List New Topic RSS
Subject Views Posts Last Post

400W 250mm heat bed Attachments

by Pippy 		79 1 02/18/2019 03:03PM
Last Post by Pippy

heated bed desing - and usage of ABS

by robvoi 		134 4 02/15/2019 08:08PM
Last Post by the_digital_dentist

Problems with a cheap titanium heatbreak

by RuiCarneiro 		209 9 02/14/2019 02:39PM
Last Post by RuiCarneiro

problem with trianglelab Bowden Extruder BMG extruder Cloned Btech Dual Drive Extruder

by marcottt 		108 1 02/11/2019 09:29AM
Last Post by marcottt

How much slop is acceptable on carriages.

by Mike_Amick 		183 8 02/08/2019 04:44PM
Last Post by imqqmi

Filament throat opinion wanted (full metal vs. PTFE lined)

by MindRealm 		143 5 02/05/2019 09:48AM
Last Post by MindRealm

Tab and slot cantilever-style platform? Attachments

by ruyvieira 		151 5 02/03/2019 10:47AM
Last Post by the_digital_dentist

30x30 print bed with single rail

by robvoi 		226 8 01/29/2019 02:35AM
Last Post by robvoi

2020/wheel vs MGN12 for x-axis

by robvoi 		152 2 01/28/2019 10:50AM
Last Post by the_digital_dentist

Which is better-Nano Smart Stepper or MKS Servo42?

by sudarshan 		165 1 01/25/2019 04:11AM
Last Post by sudarshan

Anyone Have a Moons Stepper Motor 17HD4063-01N datasheet?

by kidnamedtony 		2,874 5 01/18/2019 12:05AM
Last Post by Dust

X, Y, and Z axis. Error: printer halted. kill (Make noise) Attachments

by Abdul Mannan 		229 7 01/09/2019 01:12PM
Last Post by Abdul Mannan

Build Plate Design Attachments

by forreason 		454 9 01/01/2019 01:48AM
Last Post by MKSA

Why not to use spring tensioners on timing belts?

by dasflux 		712 23 12/20/2018 08:38PM
Last Post by ruyvieira

re anyone used Trianglelab nozzles?

by modaniel 		1,195 13 12/20/2018 10:24AM
Last Post by ruyvieira

Calculating force on ballscrew Attachments

by forreason 		206 3 12/17/2018 09:33AM
Last Post by forreason

Nema 08 via ramps 1.4?

by panterateama 		205 4 12/12/2018 06:45AM
Last Post by the_digital_dentist

Improvement on Thermistor mount and wire management!!!

by rossfree 		234 7 12/09/2018 04:12PM
Last Post by MKSA

using non-idler pulleys as idlers directly on the shaft - no bearings

by ag123 		315 10 12/05/2018 03:54PM
Last Post by dc42

Power Wiring Attachments

by FA-MAS 		1,158 26 12/02/2018 09:20PM
Last Post by PDBeal

SoM Y axis rebuild

by the_digital_dentist 		305 5 11/26/2018 03:18PM
Last Post by Ed3D

Mounting linear rails on plywood/acrylic/whatever?

by ruyvieira 		364 20 11/15/2018 04:27PM
Last Post by warbunniex

Corexy (or similar) with extened x-axis

by Pilot65 		549 11 11/11/2018 09:08PM
Last Post by ruyvieira

kraken autolift hotend Attachments

by Joar107 		2,378 9 11/08/2018 03:43AM
Last Post by evandene

Looking for 1.75mm nozzle with 1.85mm input diameter

by lukie80 		292 7 10/23/2018 08:27AM
Last Post by Srek

upgrading printer

by Blisk 		340 6 10/06/2018 05:24PM
Last Post by cozmicray

Replace timing belts with FireLine Attachments   (Pages: 1 2 3 4 5)

by j0achim 		4,310 126 10/06/2018 02:23AM
Last Post by o_lampe

E3d v6 chimera dual extruder single nozzle problem?

by malio77 		260 1 10/04/2018 08:45AM
Last Post by malio77

Advice for the self-construction of a printer and lasagne with chamomile.. eye rolling smiley

by Pinguto 		282 8 09/30/2018 12:37PM
Last Post by the_digital_dentist

Fan needed at all if not printing with PLA

by JacksonBenz 		336 7 09/25/2018 08:01AM
Last Post by Roberts_Clif
Page 1 of 35    Pages: 12345NextLast