Welcome! Log In Create A New Profile



Discuss any sort of mechanical stuff here: positioning systems, gears, extruding methods, etc. 
Subject Views Posts Last Post

Linear Guide too tight

by JoergS5
674 7 08/07/2018 04:23PM
Last Post by JoergS5

Mk8 extruder calibration problem (overextruded)

by barisali77
382 3 08/06/2018 01:43PM
Last Post by barisali77

spring steel 400mm x 400mm

by bbcbggr54
715 2 08/06/2018 01:52AM
Last Post by ekaggrat

Print bed Aluminium plate W28, EN AW 5083

by JoergS5
478 4 08/03/2018 05:52AM
Last Post by JoergS5

Lubricating Guide Carriages Attachments

by VectorRoll
1,461 6 07/15/2018 07:06AM
Last Post by JoergS5

Layer line annealing in place during print

by Infallibel
394 3 07/09/2018 06:07PM
Last Post by Infallibel

Correct way to interface braided line with stepper motor?

by Ohmarinus
785 12 07/07/2018 04:21PM
Last Post by Ohmarinus

Anet A8 Rumba Upgrade: Problem with Sensorless Homeing Attachments

by citrullin
664 1 07/06/2018 04:49PM
Last Post by citrullin

Choose my upgrade!

by cubeconvict
569 5 07/03/2018 11:51PM
Last Post by Trakyan

what is fan holder for this type ultimaker extruder clone? eye rolling smiley

by AhmedU
363 9 06/23/2018 07:44AM
Last Post by AhmedU

Seems impossible to find quality GT2 20T 5mm Pulleys

by DivePADI
773 3 06/20/2018 07:58AM
Last Post by the_digital_dentist

Staged heating extruder

by Infallibel
496 8 06/15/2018 07:40AM
Last Post by deckingman

Zwei hotends einstellen Hardware und in Marlin

by Norbert P
302 3 06/14/2018 07:55AM
Last Post by Norbert P

Drive 4 x LDO-42STH60 nema 17 with 2DM542 Microstep Stepper Motor Driver

by sz3bbylA
606 8 06/06/2018 08:02AM
Last Post by JoergS5

bed still not levelled after G29 Attachments

by golfox2
332 1 06/05/2018 05:07PM
Last Post by golfox2

Non-Captive / Hollow stepper motor for smooth rods

by makerparts
761 4 05/30/2018 01:50PM
Last Post by JoergS5

bonding aluminum - permabond?

by bbcbggr54
531 8 05/22/2018 08:21AM
Last Post by the_digital_dentist

Configuration & Settings for 5.18:1 geared Stepper?

by VectorRoll
473 6 05/21/2018 05:02PM
Last Post by VectorRoll

Mass Reduction - Bowden + Direct Drive

by Bryguy
1,026 9 05/12/2018 07:24AM
Last Post by MaIakai

Bondtech vs E3D Titan extruder - extreme torture test.

by deckingman
2,662 1 05/11/2018 02:32PM
Last Post by deckingman
This topic has been moved.

delta printer calibration

by mga
    This topic has been moved.

Anti-wobble bearing for Leadscrews Attachments

by o_lampe
1,289 9 05/04/2018 02:44AM
Last Post by o_lampe

Short intro and looking for some direction

by kattz
619 20 04/24/2018 08:14AM
Last Post by kattz

The Lampesian ZX axis: The future or just a wet dream?

by o_lampe
920 8 04/17/2018 02:16AM
Last Post by o_lampe

Comparing worm gear drives- any ideas?

by the_digital_dentist
805 3 04/16/2018 06:56PM
Last Post by the_digital_dentist

CoreXY stepper spacers... Attachments

by ampapa
953 9 04/05/2018 04:35PM
Last Post by deckingman

No DIN Rail Printers?   (Pages: 1 2)

by tgit23
2,479 37 04/05/2018 07:00AM
Last Post by the_digital_dentist

Meanwell Power Supply

by rotten_carrot
1,099 14 03/27/2018 07:38AM
Last Post by rotten_carrot

Dual extrusion setup - Which to choose?

by Banana_Luke
5,932 13 03/26/2018 05:44PM
Last Post by DutchKees
This topic has been moved.

Linear stepper motors

by klcjr89
    This topic has been moved.