Welcome! Log In Create A New Profile

Advanced

Mechanics

Discuss any sort of mechanical stuff here: positioning systems, gears, extruding methods, etc. 
Subject Views Posts Last Post

Problems with a cheap titanium heatbreak

by RuiCarneiro
1,005 9 02/14/2019 02:39PM
Last Post by RuiCarneiro

How much slop is acceptable on carriages.

by Mike_Amick
631 8 02/08/2019 04:44PM
Last Post by imqqmi

Tab and slot cantilever-style platform? Attachments

by ruyvieira
632 5 02/03/2019 10:47AM
Last Post by the_digital_dentist

30x30 print bed with single rail

by robvoi
693 8 01/29/2019 02:35AM
Last Post by robvoi

Which is better-Nano Smart Stepper or MKS Servo42?

by sudarshan
1,113 1 01/25/2019 04:11AM
Last Post by sudarshan

Anyone Have a Moons Stepper Motor 17HD4063-01N datasheet?

by kidnamedtony
4,021 5 01/18/2019 12:05AM
Last Post by Dust

X, Y, and Z axis. Error: printer halted. kill (Make noise) Attachments

by Abdul Mannan
536 7 01/09/2019 01:12PM
Last Post by Abdul Mannan

Build Plate Design Attachments

by forreason
726 9 01/01/2019 01:48AM
Last Post by MKSA

Why not to use spring tensioners on timing belts?

by dasflux
1,256 23 12/20/2018 08:38PM
Last Post by ruyvieira

re anyone used Trianglelab nozzles?

by modaniel
2,388 13 12/20/2018 10:24AM
Last Post by ruyvieira

Calculating force on ballscrew Attachments

by forreason
395 3 12/17/2018 09:33AM
Last Post by forreason

Nema 08 via ramps 1.4?

by panterateama
979 4 12/12/2018 06:45AM
Last Post by the_digital_dentist

Improvement on Thermistor mount and wire management!!!

by rossfree
438 7 12/09/2018 04:12PM
Last Post by MKSA

using non-idler pulleys as idlers directly on the shaft - no bearings

by ag123
745 10 12/05/2018 03:54PM
Last Post by dc42

Power Wiring Attachments

by blt3dp
1,672 26 12/02/2018 09:20PM
Last Post by PDBeal

SoM Y axis rebuild

by the_digital_dentist
493 5 11/26/2018 03:18PM
Last Post by Ed3D

Mounting linear rails on plywood/acrylic/whatever?

by ruyvieira
531 20 11/15/2018 04:27PM
Last Post by warbunniex

Corexy (or similar) with extened x-axis

by Pilot65
726 11 11/11/2018 09:08PM
Last Post by ruyvieira

kraken autolift hotend Attachments

by Joar107
2,594 9 11/08/2018 03:43AM
Last Post by evandene

Looking for 1.75mm nozzle with 1.85mm input diameter

by lukie80
401 7 10/23/2018 08:27AM
Last Post by Srek

upgrading printer

by Blisk
471 6 10/06/2018 05:24PM
Last Post by cozmicray

Replace timing belts with FireLine Attachments   (Pages: 1 2 3 4 5)

by j0achim
5,047 126 10/06/2018 02:23AM
Last Post by o_lampe

E3d v6 chimera dual extruder single nozzle problem?

by malio77
415 1 10/04/2018 08:45AM
Last Post by malio77

Advice for the self-construction of a printer and lasagne with chamomile.. eye rolling smiley

by Pinguto
393 8 09/30/2018 12:37PM
Last Post by the_digital_dentist

Fan needed at all if not printing with PLA

by JacksonBenz
661 7 09/25/2018 08:01AM
Last Post by Roberts_Clif

Diamond Hotend thermal insulation sheet - alternatives   (Pages: 1 2)

by zylantha
3,189 31 09/11/2018 08:07AM
Last Post by MechaBits

Where to get something like this ?

by Arnix
554 8 09/11/2018 03:49AM
Last Post by Arnix

help me identify this leadscrew? Attachments

by merlin777
436 5 08/23/2018 05:01PM
Last Post by Roberts_Clif

Linear Guide too tight

by JoergS5
662 7 08/07/2018 04:23PM
Last Post by JoergS5

Mk8 extruder calibration problem (overextruded)

by barisali77
362 3 08/06/2018 01:43PM
Last Post by barisali77