Subject		Views	Posts	Last Post
	10mm PTFE to Wade's mount by miso	882	7	12/13/2011 05:08PM Last Post by jcabrer
	Drying out PLA to reduce dribbling by fdavies	2,517	4	12/13/2011 11:55AM Last Post by Nudel
	Autoclaveable printing materials? by ropoctl	1,030	5	12/13/2011 11:11AM Last Post by nophead
	Gen 6 Electronics, heater connections? by Vortex87	1,143	3	12/13/2011 12:28AM Last Post by C. Cecil
	Mendel LITE? by jkomp316	885	4	12/12/2011 08:53PM Last Post by jkomp316
	Help with RAMPS firmware/software for Prusa Mendel by jlefebvre	1,546	3	12/12/2011 04:09PM Last Post by jcabrer
	Help support a High School RepRap club by thekendall	1,361	28	12/12/2011 11:41AM Last Post by JoeDaStudd
	How detailed can your Reprap print? by ahbtsang	1,468	4	12/11/2011 08:48AM Last Post by Petrus
	How do I complete this hot end build? by 3D2B	1,841	10	12/11/2011 07:27AM Last Post by nophead
	Standard mendel Feed/Flow rate? by Atfer	2,392	15	12/11/2011 12:50AM Last Post by NelsonRap
	www.a2aprinter.com by laomao	1,045	2	12/10/2011 10:09PM Last Post by ECSuyu
	Firmware and software issues by deltadavies	1,120	6	12/10/2011 04:55AM Last Post by jamesdanielv
	What factor make RepRap more faster & rapid by krupukbwg	2,120	10	12/09/2011 11:52AM Last Post by nophead
	Printrbot and SeeMeCNC by schorhr	1,336	3	12/09/2011 11:33AM Last Post by schorhr
	Solidoodle - any one try it? by owism8	2,291	9	12/08/2011 08:47PM Last Post by TonyC
	Frustrated by Thingiverse search feature? by zzarbi	2,411	5	12/08/2011 12:06PM Last Post by zzarbi
	Has anyone tried to turn their printer into a pen plotter? by kevinkline4124	2,848	5	12/08/2011 09:59AM Last Post by kevinkline4124
	Blew up my Hot End. by jkomp316	1,248	7	12/08/2011 03:41AM Last Post by jamesdanielv
	techzone a/d vs bed monitor by mupwi	939	3	12/06/2011 10:39PM Last Post by satsuke
	Can't load the boot loader - parallel bit bang gen 7 prusa mendle by rossfree	1,808	15	12/06/2011 03:20PM Last Post by rossfree
	Makerspace San Diego Open Invitation by MrJohn	1,847	2	12/06/2011 12:46AM Last Post by NelsonRap
	Breakaway support by ahbtsang	1,680	8	12/05/2011 07:52PM Last Post by ahbtsang
	Emaker huxley pneumatic fitting source? by 2robotguy	1,040	2	12/05/2011 07:14PM Last Post by theodleif
	Felix 1.0 3d printer: a minimalist and slick design. by MacWoodIsrael	3,473	4	12/05/2011 11:50AM Last Post by Pointedstick
	[Fixed - but why ?] Extruder chewing up filament into chips by DeuxVis	1,662	10	12/05/2011 07:17AM Last Post by NumberSix
	first layer issues by Parabolic	1,066	8	12/05/2011 07:08AM Last Post by brnrd
	Absolute Beginner To Choose First Build by STT	1,033	5	12/05/2011 04:44AM Last Post by JoeDaStudd
	Reprap policies by proctor	864	7	12/04/2011 08:34PM Last Post by NoobMan
	Prusa model 2 "does not use a print bottom plate" by tailortrik	1,485	4	12/04/2011 07:53PM Last Post by Anthong Redbeard
	Newbie needs help with sw setup for Prusa by pic1832	1,890	17	12/04/2011 03:37PM Last Post by pic1832