Subject		Views	Posts	Last Post
	Printing Issue: Wrong Temperature? by essigwurst	772	2	02/03/2013 03:35AM Last Post by mitchese
	First Print. Cant get it to flow or print right. by aplgeek	644	5	02/03/2013 03:16AM Last Post by mitchese
	DUH! Be sure to measure filament thickness!! by rtrahms	723	2	02/03/2013 02:54AM Last Post by rtrahms
	Issue with print width by maverik	1,230	18	01/31/2013 02:53AM Last Post by bravach
	Problem - Overspeeding by Mogal	1,551	8	01/30/2013 09:52PM Last Post by Sublime
	Printing issue, please,help by 4ebypek	1,073	15	01/30/2013 09:51AM Last Post by JazzyB
	Storch Purple Tape by bravach	1,186	3	01/30/2013 02:47AM Last Post by bravach
	I call this "De-laminating" or "Thermal Cracking" - but, how do I stop it! by JazzyB	4,991	12	01/29/2013 10:46PM Last Post by JazzyB
	RAMPS V 1.4 on a Prusa V2 Linear and heating problems by Heliboy	790	3	01/29/2013 11:31AM Last Post by Heliboy
	J-Head Mk IV-B Issues by 4t1fy	1,747	12	01/28/2013 07:44PM Last Post by xclusive585
	MKII Heatbed Issue: Turns off by essigwurst	888	7	01/28/2013 01:27PM Last Post by maverik
	My print always stops-cold about 4cm up on the Z-axis by [email protected]	734	5	01/28/2013 01:20PM Last Post by maverik
	Wrong height and width by demetris	1,154	5	01/27/2013 05:01PM Last Post by demetris
	Excess PLA on first layer - what am I doing wrong? by rtrahms	1,210	7	01/27/2013 02:07PM Last Post by rtrahms
	Tips and tricks to print a circular object. (The wrong way) by EMH Studios	1,408	5	01/26/2013 11:59PM Last Post by EMH Studios
	PLA not sticking to glas by holgero	2,692	13	01/26/2013 06:43AM Last Post by holgero
	Z axis too smal roation, Prusa Mendel. by cstudio	2,193	7	01/26/2013 05:55AM Last Post by Staseek
	first few prints, major issues by quantize	2,045	21	01/23/2013 07:00AM Last Post by Sublime
	a troublshooting-faq ??? / my extruder blocks after 30 minutes :'( by roland	1,470	8	01/21/2013 01:06PM Last Post by roland
	What is going on with this print? by rtrahms	2,312	12	01/21/2013 05:34AM Last Post by Speedsoda
	What causes little holes in the surface? by fsamir	1,301	11	01/21/2013 05:31AM Last Post by Speedsoda
	One "quadrant" printing bad. by phroid	740	4	01/19/2013 11:22PM Last Post by xclusive585
	Smallest nozzle ever? by sungod3k	1,175	10	01/17/2013 05:37AM Last Post by nophead
	Prints leaning to side by Matouš	1,098	3	01/17/2013 05:22AM Last Post by Matouš
	printing quality at small parts by Irgendwer_Aus_Irgendwo	1,145	8	01/16/2013 09:23AM Last Post by Irgendwer_Aus_Irgendwo
	Layer alignment issue by kri	747	4	01/13/2013 12:23AM Last Post by tsb4k
	Last layer incomplete by Megdor	901	5	01/12/2013 02:52PM Last Post by swhitlock
	circular top layer issue. by fixedtrd	623	2	01/10/2013 10:44AM Last Post by Chipper
	prints go bad after a cm high or so? by rrr7	1,937	4	01/10/2013 08:16AM Last Post by rrr7
	printing issues by printman	807	2	01/09/2013 08:11PM Last Post by printman