Welcome! Log In Create A New Profile

Advanced

Repetier

Subject Views Posts Last Post

Current status of autolevel in repetier 92.4

by sungod3k
772 1 09/16/2015 03:45AM
Last Post by sungod3k

Repetier Host on Mac

by Francois
676 1 09/13/2015 11:25AM
Last Post by Francois

Two Steppers for Y - How?

by Reparator
688 3 09/13/2015 10:03AM
Last Post by Reparator

RH Park position is not activated after Job

by justcurious
679 2 09/13/2015 08:58AM
Last Post by justcurious

Repetier 0.92.x - Dokumentierte Configuration.h

by Reparator
682 2 09/13/2015 04:33AM
Last Post by repetier

RH printer connect has hickups

by justcurious
1,099 28 09/13/2015 04:28AM
Last Post by repetier

Invalid Delta Coordinate - Move ignored Issue Attachments

by Moesling
1,263 9 09/09/2015 09:31AM
Last Post by repetier

Problem with 0.92.4 Firmware and watchdog Attachments

by Gurgi
1,447 4 09/06/2015 05:15PM
Last Post by Gurgi

Reason for: Printer reset detected - initalizing

by 4Stroke
2,021 2 09/01/2015 09:35AM
Last Post by repetier

1.5.5 Autotune heated bed time out (just keeps heating)

by DSteck
737 1 08/31/2015 01:55PM
Last Post by DSteck

Repetier as CNC

by romaytech
986 1 08/27/2015 11:36AM
Last Post by romaytech

A problem found with 1.5.4 Attachments

by frankleng
802 5 08/25/2015 08:57AM
Last Post by repetier

heater relay fast clicking problem

by Kryoclasm
647 2 08/24/2015 08:43PM
Last Post by Kryoclasm

Novel Ooze-Elimination Dual Extruder Retraction Attachments

by TheHackerArtist
1,974 3 08/24/2015 08:01AM
Last Post by Andy1989

Repetier Firmware .83 and the LCD Controller

by Tsenneville
692 2 08/21/2015 03:17AM
Last Post by repetier

Eeprom loses data

by 03daniel11
699 1 08/19/2015 02:50PM
Last Post by 03daniel11

Steppers wont move and other errors on my gMax 1.5 with Repetier

by Fender
756 2 08/19/2015 02:15AM
Last Post by repetier

How to run fans with rumba board?

by slonik
5,427 13 08/19/2015 02:06AM
Last Post by repetier

LCD Z-Leveling

by maralb
696 1 08/17/2015 12:30PM
Last Post by maralb

I have a da vinci 1.0 and just flashed it with repetier. Need help with leveling?

by Tawmiller
958 2 08/15/2015 04:11AM
Last Post by repetier

Slicer eliminating bottom layers Attachments

by sigilwig44
689 1 08/13/2015 10:48PM
Last Post by sigilwig44

Cura in Repetire -host

by Geartech
1,144 4 08/12/2015 09:18AM
Last Post by Geartech

End script error

by Renatfg
701 4 08/11/2015 04:52AM
Last Post by Renatfg

Z Offset In Repertier Host ?

by scubi
3,759 2 08/10/2015 03:22AM
Last Post by repetier

Thermocouple table for AD597

by Kryoclasm
977 3 08/08/2015 07:32AM
Last Post by Kryoclasm

Dual extrusion offsets in Repetier Firmware

by smartroad
1,497 2 08/08/2015 06:53AM
Last Post by repetier

Can't get infill to connect Attachments

by icius
659 2 08/07/2015 08:30AM
Last Post by icius

Repertier Host v1.5.3 no numbers on dials

by scubi
709 6 08/06/2015 05:56AM
Last Post by repetier

Can't get my Azteeg X5 mini board to move any of my steppers in Repetier Host Attachments

by lornetw
995 1 08/05/2015 07:56PM
Last Post by lornetw

dry run?

by sarf2k4
1,864 4 08/04/2015 03:36PM
Last Post by sarf2k4