Welcome! Log In Create A New Profile

Advanced

FoldaRap

http://reprap.org/wiki/FoldaRap and her younger sister Mondrian http://reprap.org/wiki/FoldaRap2 
Subject Views Posts Last Post

IceSL slicer

by Emmanuel
1,744 3 08/15/2014 08:07AM
Last Post by Emmanuel

pliage de la foldarap

by Zotur
1,516 2 07/30/2014 06:06AM
Last Post by -=Pascal=-

Probleme d'alim et de chauffe de la tête d'extrusion

by Zotur
1,550 3 07/30/2014 03:17AM
Last Post by Zotur

problème de connection avec pronterface

by Zotur
2,262 6 07/27/2014 03:47PM
Last Post by Zotur

Montage foldarap 148

by nicobuzz
1,464 15 07/23/2014 07:55AM
Last Post by Ploom

Probleme électrique minitronic

by Ayato86
1,440 12 07/22/2014 05:49PM
Last Post by Ploom

quelle carte choisir ? Attachments

by kourou
1,590 1 07/21/2014 07:28AM
Last Post by kourou

Calibrage / respect des dimensions des pièces imprimées

by dethegeek
1,272 4 07/15/2014 09:34AM
Last Post by loic.fejoz

Infill Gap - Remplissage insuffisant

by Thiasma
1,210 2 07/08/2014 11:51AM
Last Post by Enrico

Questions montage Foldarap #166   (Pages: 1 2)

by dethegeek
2,866 33 07/05/2014 02:27PM
Last Post by dethegeek

Branchement des ventilateurs sur la minitronics

by Enrico
1,154 4 06/25/2014 02:20PM
Last Post by dethegeek

#162: problèmes de géométrie [résolu]

by Enrico
1,173 6 06/13/2014 06:45AM
Last Post by Enrico

Kapton 20 cm width Attachments

by Foldarap85
1,252 4 06/11/2014 05:13PM
Last Post by schweini2409

Question montage foldarap #165

by jomonbre
1,161 5 06/11/2014 02:24AM
Last Post by -=Pascal=-

Foldarap #154 pic & Z-axis print start point issue Attachments

by Senake
1,072 2 05/26/2014 11:57AM
Last Post by Enrico

Recherche du jeux optimum sur les glissières x et z de la FoldaRap2

by -=Pascal=-
1,276 6 05/24/2014 05:03AM
Last Post by mattsi

Réglage axe Z

by al44
1,074 4 05/18/2014 05:06AM
Last Post by -=Pascal=-

Foldarap 141

by Khoi
1,667 24 05/16/2014 07:35AM
Last Post by Khoi

Hotend Problems

by tyler_waite
1,318 7 05/16/2014 07:11AM
Last Post by Foldarap85

[réglage] La technique du crayon Ikea...

by -=Pascal=-
1,518 1 05/15/2014 06:51PM
Last Post by -=Pascal=-

Nozzle leaking

by Thiasma
1,916 6 05/12/2014 05:06AM
Last Post by laurent_P

Z axis problem printing

by nachetz
964 3 05/09/2014 12:10PM
Last Post by mattsi

JHead mount on latest x-slider and stock extruder mount

by jamesmoe
1,165 3 05/07/2014 07:00PM
Last Post by jamesmoe

Extruder thermistor not reading on Geeetech Melzi board

by mrjazzitup
1,688 3 05/06/2014 06:13PM
Last Post by mrjazzitup

After some weeks with my Foldarap. Attachments

by Foldarap85
1,717 7 05/04/2014 08:28AM
Last Post by laurent_P

[mod] Down blower

by laurent_P
1,273 10 05/03/2014 03:23PM
Last Post by mattsi

X & Y axis problems

by nachetz
1,083 4 05/03/2014 01:32PM
Last Post by nachetz

Which Foldarap 2 firmware ?

by Khoi
1,233 5 05/03/2014 01:24PM
Last Post by Khoi

settings correct pin #s in pins.h

by mrjazzitup
1,501 1 05/02/2014 03:42PM
Last Post by mrjazzitup

Foldarap : Configuration Moteur

by al44
1,033 4 05/01/2014 06:49AM
Last Post by Khoi