Welcome! Log In Create A New Profile

Advanced

Problémy

nefunguje to 
Page 3 of 9    Pages: Previous12345NextLast
Forum List New Topic RSS
Subject Views Posts Last Post

Nefunkční tisk z SD karty

by Hor_cz 		734 6 02/02/2016 10:21AM
Last Post by Bery

Tisk není vycentrován

by profano 		852 22 01/28/2016 08:17AM
Last Post by profano

Kalibrace os???   (Pages: 1 2)

by IkaSGC 		2,819 40 01/19/2016 02:45PM
Last Post by petrk

zahřívání motorů

by paycz 		639 9 01/19/2016 07:02AM
Last Post by paycz

Tiskarna tiskne moc plastu

by PazziCZ 		710 7 01/18/2016 03:07PM
Last Post by PazziCZ

tisk na kovoví plech

by paycz 		803 7 01/13/2016 03:19PM
Last Post by paycz

Testovani mechanickych vlastnosti vytisku

by misil 		577 1 01/12/2016 04:55PM
Last Post by misil

Kalibrace osy z

by vladcev 		710 8 01/08/2016 06:11PM
Last Post by misil

Kvalitnější tisk

by paycz 		629 3 01/07/2016 10:03AM
Last Post by straciam

problem s hotendem, nebo extruder?

by Spoach 		939 11 01/06/2016 04:10PM
Last Post by misil

problemy s low-cost tlaciarnou Attachments

by straciam 		1,360 21 01/01/2016 08:02AM
Last Post by misil

tisk více objektů

by paycz 		571 7 12/31/2015 12:25PM
Last Post by misil

Mach 3 Pomoc .

by milou 		1,570 7 12/30/2015 02:54PM
Last Post by W1mpy

Občas nejede forum

by milou 		597 3 12/12/2015 04:19AM
Last Post by milou

Filament vyjíždí z extruderu

by paycz 		899 11 12/06/2015 02:34PM
Last Post by straciam

Je to normalni ? Attachments

by paklic 		772 11 12/02/2015 03:50PM
Last Post by raptik

testovaci kosticka - deformace pravych hran

by misil 		2,239 25 11/27/2015 07:35AM
Last Post by jakvok

velleman k8200 mainboard

by HonzaCerny 		615 7 11/20/2015 01:25PM
Last Post by dan

PLA a celokov

by dan 		2,895 25 11/20/2015 12:12PM
Last Post by Korny

Časté ucpání hotendu

by vinchi9 		1,808 6 11/09/2015 03:42PM
Last Post by dan

Problém s termistorem a podložkou

by Nothrax 		638 3 10/31/2015 04:54PM
Last Post by misil

Problém při tisku malého stojatého profilu

by DuckD 		571 3 10/16/2015 10:46AM
Last Post by raptik

problém z pronterface

by Rossky 		820 3 10/15/2015 05:18AM
Last Post by Rossky

Tisknutí bez dohledu

by pinkolin 		611 8 10/13/2015 05:23PM
Last Post by lubosjerabek

coreXY problém

by PIMPin 		606 1 10/13/2015 06:08AM
Last Post by PIMPin

Netiskne to.....

by IkaSGC 		751 10 10/10/2015 06:31AM
Last Post by IkaSGC

Výpočet řemene z osové vzdálenosti .

by milou 		1,517 4 10/06/2015 01:57AM
Last Post by milou

Nelze připojit !!!

by Tony3 		741 8 10/01/2015 03:47PM
Last Post by Tony3

Rada ohledne tisku PLA-D Attachments

by Deathmann 		947 22 08/30/2015 05:45AM
Last Post by Deathmann

Nefunguje vždy jedna osa !!!pouze při tisku!!!

by Bojkas 		653 1 08/27/2015 04:33PM
Last Post by Bojkas
Page 3 of 9    Pages: Previous12345NextLast