Welcome! Log In Create A New Profile

Advanced

Problémy

nefunguje to 
Page 5 of 9    Pages: FirstPrevious34567NextLast
Forum List New Topic RSS
Subject Views Posts Last Post

přerušený tisk

by petan86 		947 6 04/04/2015 08:09PM
Last Post by trilobit

Nastaveni sliceru aby zacinal kazdou vrstvu v jinem miste ?

by bluewave65 		718 6 04/04/2015 04:11AM
Last Post by bluewave65

Jak vytvorit 1 servisni vrstvu ?

by bluewave65 		639 2 04/03/2015 01:41PM
Last Post by dan

Potíže při tisku větších objektů Attachments

by tomasn 		936 13 04/03/2015 11:09AM
Last Post by tomasn

Ryje pri tisku v materialu - PLA od mladece

by bluewave65 		909 12 04/02/2015 07:45AM
Last Post by bluewave65

Zvlastni hodnoty pri PID kalibraci ?

by bluewave65 		985 6 03/23/2015 04:12PM
Last Post by raptik

Kde v MARLIN FW nastavit HOMESWITCH offset ?

by bluewave65 		818 2 03/18/2015 06:40AM
Last Post by Bulman

Napojení řemenu T2.5

by milou 		728 1 03/17/2015 01:46PM
Last Post by milou

extruder zly posuv

by minicico 		792 7 03/11/2015 10:29AM
Last Post by minicico

Problém s tiskem pod uhlem

by yety 		684 1 03/11/2015 06:18AM
Last Post by yety

vypne sa vyhrievanie trisky

by risoo 		843 5 03/04/2015 06:26AM
Last Post by MaSeRcZ

motor extruderu - nejede

by zlygriz 		726 8 03/02/2015 04:41AM
Last Post by zlygriz

Filament Mladeč

by CADS 		3,661 24 02/25/2015 10:05PM
Last Post by Korny

Problém s připojením.

by hlaseklukas 		738 5 02/19/2015 03:02PM
Last Post by raptik

Problém s osou Y

by juricaj 		707 4 02/17/2015 01:19PM
Last Post by juricaj

sikma vypln na 100 -lze to zmenit? Attachments

by paklic 		609 2 02/16/2015 12:58PM
Last Post by PIMPin

dobiha me marerial

by Ditr 		788 7 02/09/2015 02:27PM
Last Post by Vinie

Zaseknutí pojezdu osy Y

by boylucky 		810 4 02/07/2015 08:25AM
Last Post by boylucky

retraction

by lici 		617 2 02/07/2015 07:31AM
Last Post by raptik

podivne "zapominani" gcodu?

by raptik 		735 7 02/01/2015 03:51AM
Last Post by raptik

spatne nastaveni nebo slic3r ? Attachments

by paklic 		1,040 7 01/11/2015 08:40AM
Last Post by raptik

prilnavost ABS na karbon Attachments

by chaluha 		939 3 12/31/2014 10:55AM
Last Post by chaluha

problem motory sa tocia iba jednym smerom

by torrus 		829 9 12/27/2014 06:51PM
Last Post by torrus

velikost vytisku neni presna

by Bajn 		984 9 12/16/2014 01:58PM
Last Post by raptik

Bublinky při extruzi filamentu.

by gumitek 		1,755 7 12/15/2014 04:39PM
Last Post by jirpil

Tisk s 2 extrudery   (Pages: 1 2)

by dan 		3,269 35 12/12/2014 09:42AM
Last Post by olisoft

Problémy s vytlačování materiálu Attachments

by cernra 		819 5 12/05/2014 12:20PM
Last Post by cernra

Špatné rozměry modelu

by Kouďák 		713 2 12/02/2014 08:58AM
Last Post by raptik

Hotend pre plast z czechreprap

by SOGOR 		898 6 11/27/2014 04:20AM
Last Post by zemciko

Problém z výplní [Slic3r 1.1.7] Attachments

by helios 		757 6 11/27/2014 03:53AM
Last Post by raptik
Page 5 of 9    Pages: FirstPrevious34567NextLast