the same story is comming along x, y and 45 degree is an core xy I ask myself if can be from z axisby sz3bbylA - Printing
I build a core xy 700x500mm motors are 3amps nema23 with klipper and octoprint it is not set completly in klipper I set an delay for drivers like 3usec to eliminate posibility loosing steps for the first prints is looking good the problem is this layers are not alingned verticaly one of each belt have around 5 metrs and are very long in my opinion I left it little bit loose , I tight it , the fby sz3bbylA - Printing
I wired straight from pin fan arduino and is working I'm not sure if must use that resistor 10k now is working without that resistor but I would like to know why some people are use it for different materials i use a dimmer to control power intensity and also still in testing trying to print images so i have variable intensity 0 to 255 also variable power true laser from dimmer maybe somebody kby sz3bbylA - Laser Cutter Working Group
I just bought this laser from aliexpress is a 2 W laser I connected to my radds on fan pin 2 and used with commands M106 P1 Sxxx on, and M107 P1 off is working but i want to try TTL controller for this board is the problem is I use RADDS with arduino due and pinout are on 3.3 v I try to figure out how to use it with my board true TTL I am not sure but i try to draw a small schematic usby sz3bbylA - Laser Cutter Working Group
I bought this toy over ebay and I was surprised when I saw there is no info on internet about motors This lens got 2 motors steppers , mini, and when I measured there are 2 coils 39.3 ohms means are normal steeper motor maybe somebody have a clue how can I drive this motors, which drivers i need to be used thank youby sz3bbylA - General
I come back with new info I think my arduino due is not original On radds 1.6 I found an circuit closer to display pinout HCT365 2L5E401, i think is an TTL logic for display but i don't know how to test it if is broken or not I measure circuits for termistors and look ok if I try to heat nozzle or bed , they are working temperature nozzle is showing, temp bed remain the same 4 degree M119 , teby sz3bbylA - Controllers
I just buy few days ago RADDS 1.6 arduino due RADDS lcd 20x4 char core xy x, y z, are controlled by 2DM542 with nema 23 , so I took from board only EN , STEP, DIR and GND, increasing high_delay 5, and double_step_delay 2 extruder is controlled by A4988 , is an 0,9 degree from E3D I try to put repetier 1.0.2 but without success Problems: 1. After few rewrite firmware LCD begin to show me onlyby sz3bbylA - Controllers
I write again about this situation because I don't find a real solution for it I build a core xy and i intend to use repetier firmware on my ramps 1.4 my problem is after uploading the firmware my printer is not moving right my printer is core xy full discount display ramps 1.4 if i try moving on x +, my printer go on x if i try moving on x -, my printer not moving if i try moving on y +, my pby sz3bbylA - Repetier
I got 4 motors nema 17 LDO-42STH60-2004AC and I like to know if there any chance to drive it with a single 2DM542 Microstep Stepper Motor Driver I plan to put a motor in any corner of surface to lift it. motors are 2 ohm on my multi meter I don't find on internet if is ok to put motors serial or paralel connection or is something more mast can do to make-it working thank youby sz3bbylA - Mechanics
I just buyed a silicone ruber made with imported material from china i realy don,t know wich kind of material is this but i tryed to stick on glass with double adesive tape and don't keepet sticked look like a silicone with somethng glass fiber i ask for somebody who buyed something similar wich double adesive mast use to stick on glass ? thank you and scuse my englishby sz3bbylA - General New Machines Topics